MDE14PSADW Maytag Dryer - Instructions

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

I watched a video on YouTube for the disassembly of the dryer. The parts replacement took less than 20 minutes; the rest of the time was spent on disassembly and reassembly.

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

Moved the front door/panel two screws at the bottom of the panel.Then removed the front plate and support for the drum assy. four screws.Then loosen the belt and removed the drum assy. to get access to the drum roller to the back top right,.Used snap ring pliers to remove the clip cleaned the shaft an installed the new roller with the fiber washers and installed per instruction from your video,Also replaced the belt and put all items back in reverse order.It worked like a champ so easy,I would recommend your web site and videos to any one who wants to do it yourself. I have used you in the past and will continue using you for other items for parts and support.

Followed the video. Hardest part was getting the belt around the ideler pulley and motor pulley without seeing. But I got it! Thanks to this site you rock!

With the parts in hand, and after disconneting power and shutting off gas line, I again removed the door, front panel and front tumbler frame to expose the blower wheel. I discovered that the blower wheel was not damaged, but that compressed pieces of lint and other items where stuck to the wheel. I removed the pieces and vacuumed the the whole thing clean, tested it, and the sound stopped. Since I had the unit open, I replaced the front glides by drilling out the old rivets, removing the old glides and then riveting the new glides in place. A very simple procedure overall.

Make sure you keep track of where the different screws go and keep them inside something so you don't lose them. I also used my cell phone to photograph various areas and screws for later reference.

Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.

I had to remove the door first. Then the retaining brackets that hold the upper lid on. This also allowed removal of the front cover. After releasing the tension of the drum belt, I removed the drum and replaced the drum roller in suspect. Installation was reverse in order. Don't know why I waited so long to do such a simple job.

repair was pretty easy, actually took more time removing the door and the front housing that actually changing out the rollers

Received parts within two days of order. thank you

The hardest part of this repair was diagnosis. After running continuity tests on the electrical components, removing the heating unit showed a broken filament on the heat coils. The replacement part fit mechanically, but used spade terminals for high voltage instead of the original mounting posts, requiring retermination of the wires. One of the power leads also had to be extended in length. All works after completion.

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.

I re-assembled, checked felts, and wear blocks,(good condition). I cleaned lint, removed coins from baffles, corrected several dents(minor), double checked wire condition and routing (good), finished re-installation, checked balance . all was good, and ran two loads of laundry. very quiet! Thanks

I've had this dryer since it was new It's over 25 years old. and it started to make a high pitch squealing sound when in use. Decided it's time to repair it. a new one is very expensive. So I ordered the parts from this site. When the parts arrived they where Inspected for fit, function and finish. So I proceeded with doing the repair myself. Short Phillips screw driver to remove the two sheet metal screws at the bottom front panel. tilted the panel from the bottom outward and removed it from the main tumbler cabinet. labeled the door switch wires one was yellow & one white. so I would not reinstall them incorrectly upon assembly. removed the front panel. set it aside. then removed the bulkhead panel 5/16" screw in each corner. removed that and set it aside. and there she was, the tumbler. I pulled the tensioner up to loosen the belt, and removed it. then grabbed the tumbler from the inside top slightly picked it upward and slid it out of the cabinet exposing the two rollers and axles one on each side that it sits on. at that point I noticed the drive belt was frayed and slightly worn. came back in the house and got on line ordered a new one from Parts Select it showed up a day later and a perfect match. the rollers are held in place by snap rings at the end of the axles. squeeze them they come off real easy, and on the back side there's a 14mm hex head nut. box wrench works good here to loosen the nut and remove the axles. the original washers are metallic and worn badly, they where making the high pitched squealing sound when they rotated so they came off and where replaced by the ones in the new roller kit and lubed with graphite not oil or grease. Graphite is dry and does not collect all the dirt and debris. put the new washers, new rollers & snap rings back on the axles grooves on the end, hand spun them and they where ready to roll. took the new belt placed it around the tumbler over the exact witness marks that where there so it would line up and lifted the tumbler back into the cabinet aligned the new belt over the motor pulley and tensioner lining it up exactly on the witness marks left by the old belt. slowly slid the tumbler back on to the new rollers rotated the tumbler a couple rotations clockwise to set the belt put the bulkhead back on the front with 5/16" sheet metal screws. in 4 corners, reinstalled the from panel along with the door switch wires and it was done. now the moment of truth. plug the machine in and turn it on!. Bingo! it runs so well you don't know it's even running. after this repair the machine performs even better. it actually takes LESS time for clothes to dry! AJS