MDE7758AYQ Maytag Dryer - Instructions

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

First let me say I went on your forum and got instructions where to download a service manual which helped greatly. Unplugged from outlet. Removed 4 screws holding on the front panel then 4 more holding on the front tumbler support and air duct. Removed wires from light and dryness sensor and clips holding wires to panels. Pulled out the tumbler and removed belt. Removed the two drum support rollers and shafts by removing a nut on the back side of each shaft. Removed snap ring off each old shaft, installed new rollers and fiber washers onto new shafts installed snap ring and replaced on brackets with the old nut. Removed tension spring off idler pulley bracket and one screw holding on the bracket. Installed new pulley and fiber washers on new bracket and reinstalled bracket and spring. Placed new belt on tumber and reinstalled tumbler. Used drill and bit to drill out pop rivits holding on the two front glides that are attached on the front tumbler support and installed new glides and pop rivited in. Reinstalled
front support and air duct checking that felt tumbler seal front and rear were in place. Placed new belt on motor pulley and idler pulley. Reinstalled front panel. Removed bulb cover held on by one screw, Installed new light bulb. Also took shop vac and cleaned inside of cabinet when I had the tumber out. Plugged back in and started, sounds and works like new. Ordered parts on Sunday received Tuesday evening Fed Ex. First time dryer repair. Very happy with PartSelect web site and service.

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

took out the old lint filter and put in the new one.

It fit perfectly! the part arrived quickly.

I was very satified with my experience!

I had to call and reorder because I ordered the wrong part and the gal on the phone cancelled the first order and the right part came the next day!Amazing service!!!

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

remove back cover 3 screws, change wires in same order as old timer, remove two mounting screws under timer dial, check voltage-replace temp sending control attached to brown wire.

The video was excellent and made for an easy repair. Would highly recommend.

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.

replaced

We inherited this dryer three years ago upon purchasing our current house. At that time I found this website to purchase and install a couple of the baffles that were missing. This time, I checked the troubleshooting for my current problem and ordered all of the parts I felt I needed to resolve the problem. Once I received the parts, I followed the great how-to videos by Steve to disassemble the front of the dryer and remove the drum. I could not get to the repairs right away since the interior of the dryer was quite dirty and I took a lot of time to clean it out. Once I got to removing and replacing the drum rollers, idler pulley, rear drum felt shaft, and drum belt, everything went smoothly and was just as easy as Steve described in the videos. If I didn't have such a dirty machine interior, removing the old parts and installing the new parts would have taken less than an hour. I had to hold off on installing the front glide kit and front drum felt seal since I forgot to order two of each (I'll install these at a later date. I proceeded to putting everything back together and testing the dryer. The dryer now runs quietly and works great.

Removed the old filter and replaced with the new filter. It's just like cleaning the filter.

Part replacement

Replaced timer dial skirt. Use small screwdriver to take broken part. Snap in new skirt and slide skirt on stem. Could not push skirt flush down all the way to the panel, but it works.