MDE26MNACG Maytag Dryer - Instructions

After viewing repair video I used those instructions, after removing drum place new belt on drum, I used scotch tape to hold belt in place, tape belt with 2 inch strip about every foot around drum, leave extra belt that connects to drive motor folded down and taped to drum. After installing drum connect belt to drive motor and roll drum to remove tape. This will keep belt from sliding out of place on drum while installing.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

Opened your replacement part and found a broken fin on the blower wheel. no way I was going to return it and wait another week for another part. Perhaps you folks need to inspect what you send out. 1 blower wheel with a broken fin and 2 clamps. Replacement was easy and quickly accomplished. Having replaced drum rollers and the belt this dryer is almost new. Thanks

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

Pried off old pads - used hammer to tap on new pads.

Locating replacement parts was the problem until I found partselect.com

took out old and placed in new

Removed the two lower screws holding front of dryer assembly in place and "unhinged" it and stood it up on floor. Then I unclipped the two wire leads on inside of dryer door assembly and moved assembly completely out of work area. Next I removed the four screws holding the tumbler frame in place and removed that frame from the work area. Now you can access the blower wheel "frame" and remove 5 or 6 hex screws to get that off and out of your way. You DO NOT have to remove the dryer drum and/or drum belt to complete this repair, so save yourself some work and leave it in place!! Once the blower wheel frame is off, use pliers and a flatheaded screwdriver to get the small outer retaining clip off, and then just pliers to get the wheel retaining ring off the wheel shaft. Put on the new blower wheel, use pliers to replace the aforementioned wheel retaining ring, and then the small outer retaining clip...VIOLA! You're finished! Dryer will run like new with a smooth purr instead of that dreaded rumbling sound.

Followed instruction video

Removed back panel of machine which exposed badly worn idler pulley. Have had problem before on another dryer so I was sure what problem was before I started. Removed snap washer and cloth washer and then bad pulley.(It was very worn and wobbly).Cleaned shaft with small piece of emery paper and put two drops of oil on shaft and replaced old pulley with new one.Put back washer and snap washer.Drive belt had slipped away from its proper position so I had to remove the front panel of the dryer to place the belt back and realign it on the drum and around the new pulley and the motor drive shaft. Not really that difficult.....Machine now runs like it's brand new.....

Turn off circuit breaker or unplug. Remove two screws 4 inches from bottom front panel of cabinet with stubby phillips head. Pull panel towards you about 30 degrees; then wiggle it down, to free two steel spring clips holding it to cabinet. Pull off red and yellow wire from door switch. Now set front panel aside. Blower assembly is facing you at lower left. Open the housing by removing six small screws from cover and one attached to dryer base. Remove spring clip from end of shaft. (A circlip pliers helps to prevent it from springing off somewhere.). Squeeze spring retainer surrounding blower wheel shaft with regular pliers, and wiggle the blower off. Replace in reverse order. Be sure insulation around blower wheel housing seats properly into front panel. This keeps the hot air flowing up past the lint trap.
Easy job, about half hour. Mine took longer, because I had removed the belt and drum, thinking the noise came from bad drum support rollers. It was just the plastic blower wheel shaft seat, which had worn itself round. Cost $20 (including shipping) and my 29-year old Maytag is as good as new--at least for now.

I UNPLUGGED TH UNIT.Removed the 2 screws holding the front panel in place, disconnected the electrical leads on the panel. These screws are located on each side of the panel 3 in. from the bottom. Removed the 4 screws holding the shroud. Disconnected the ground wire on the shroud & set both aside. Installed the new belt per the diagram & instructions. Turned the tumbler by hand a few times to verify proper installation. Re-installed the shroud & front panel including reconnecting the leads & ground wire. You need to use both hands in a tight space to install the belt on the pulley & guide(a littledificult) The new belt fit perfectly & the instructions were easy to follow & accurate.

I bought this machine in 1984. For the belt to last this long, is extraordinary. The belt comes in a plastic bag with instructions. After removing the front cover(2 screws at the bottom, tip bottom out towards you. Cover unhinges from the top. Lean face against a wall. Don't remove any wires). I then vacuumed the inside thoroughly. Used a parts brush to wipe everything off, and blew out with compressed air. Vacuumed again. A bit obsessive, but gas and dust are not a good combination. So why not take the extra time. There is a continuous mark on the circumference of the drum, left by the original belt. Use this as your guide to locate the new belt. Rotate the drum by hand to make sure it tracks correctly. I also ran the motor with everything open, to make sure everything was cool before I buttoned it up. Also took the time to replace the gas line with a new one, and duct-taped the vent pipe to improve air flow.

This dryer has been really reliable. This is the first time I've had to repair it. PartsSelect.com says the noise had a 30% chance the problem would be the tumbler rollers and shaft and 18% it would be the blower impeller fan. I took a chance on the rollers, thinking I would save $20 on the blower fan. Big mistake! Once I dissambled the dryer, I realized almost immediately it was the blower fan and not the rollers. When I manually turned the motor shaft, I discovered the problem. The plastic fan's shaft hole is worn to a larger diameter and is semi-freewheeling on the shaft causing the racket. I replaced the rollers and belt and ordered a new fan. I tried putting electrical tape on the shaft to enlarged the OD like a fellow on this site said, but it worked for about 3 minutes then the racket started again. Also, I had to pull the dryer away from the wall and open the access door to the back of the motor in order to thread the drive belt on the motor and idler pulleys. I couldn't fit my arms along side and under the tumbler. I've got the scratches on my left arm to prove it. Suggestion: Replace the blower fan, rollers and shafts if you have the rumbling noise when operating the dryer. Might as well replace the drive belt while you have it apart, too.

Fast receipt of parts from supplier . All parts went together very quickly. Don/t recommend this work for those who have no mechanical skills. realignment of screws can be very tricky . They must all be correctly aligned first and driven in at diagonals to equalize pressure . Job needs to be used with hand tools as it is easy to strip out the threads in dryer by overtightening the screws.
PS before this we had replaced the drum belt.
Update:
We ran the dryer after replacing the drum support rollers and the idler pulley and it was smooth for about 5 minutes. then the rumbling and uneven rotation started up again! The tip-off was when we had done a test roll on the drum after changing the above parts, we heard a rumble from the blower wheel! so we ordered the blower wheel, replaced it and the dryer sounds like new.
Thanks to others who have written their stories which helped us figure out the problem. : ) saves big $$ on buying a new dryer. PS ours is 15 years old and has had heavy use.