MLE15PDAGW Maytag Dryer - Instructions

first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.

Remove the door and front cover ,then the top flips up ,remove the front drum support then the drum,remove the snap ring and the pulley

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

followed instructions on youtube. The only hitch was threading drive belt back on. the video showed from back instead of front.After I was done I noticed an access door in back that would have helped.

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

I use U Tube watched Video, you have to take apart the dryer, but pretty simple to do. The drum rollers were very easy to install, make sure to have snap ring plyers, installing belt was easy too, make sure to put it back on it the way it came off, mine was ribbed side down on drum. Take a picture if necessary. Getting the belt on the pulley right is the most important part, the rest is just reassembling,

I followed the YouTube video for pulling the heating element to remove and place the thermostat. The actual thermostat removal and replacement was pretty simple. Most of my time was spent removing the front panel, pulling and reinstalling the heating element.

As the dryer would be going you could hear a grinding noise every other sec or so, like sandpaper sanding metal.

Disassemble as per video on this site and install replacement felt seal.

Took a bit to tear down and change and reassemble but well worth the time as there is
no one in our area that does this type of repair(s) any longer

Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that

Removed the door then removed front panel then removed 8 screws that held the drum in. At this point reached in and removed the snap ring on the wheels and replaced the washers and wheels. Then reassembled it.

My son did the repair work. He took off the door and then carefully unhooked the belt and removed the drum. Replacement on the drum roller kit went smooth, and he then oiled the idler pulley while he was in there. I now have a "quiet dryer" once again!!! Had orderd the wrong part to begin with, but was very easy to return, receive my credit and get the "right" replacement part.
Great Service!!!!

I removed and replaced all the problem pieces, and now she runs better then when I got her!

Moved the front door/panel two screws at the bottom of the panel.Then removed the front plate and support for the drum assy. four screws.Then loosen the belt and removed the drum assy. to get access to the drum roller to the back top right,.Used snap ring pliers to remove the clip cleaned the shaft an installed the new roller with the fiber washers and installed per instruction from your video,Also replaced the belt and put all items back in reverse order.It worked like a champ so easy,I would recommend your web site and videos to any one who wants to do it yourself. I have used you in the past and will continue using you for other items for parts and support.

Followed the directions of the video and all went smooth. Cleaning the lint and parts was the more time consuming than the actual repair. 30 minutes for the repair and an hour for the clean. All and all very easy.