MLE15PDAGW Maytag Dryer - Instructions

This was pretty much as easy as most other folks had described on this site.
1. Removed the two screws at the front bottom that are holding on the fromt panel, and then lift up and remove the panel.
2. Disconnect the door-open-safety-switch, remembering which color of wire goes on which connection.
3. Remove the four screws (two on each side) on the front bracket that supports the drum and tthat contains the front glides.
4. Remove support bracket and lint trap, letting the drum rest gently on the stuff underneath.
5. Remove the screws holding the lint trap to the support bracket. (My model had five screws.) Remove lint trap from support bracket.
6. Drill out the two pop rivets on each of the two glides, noting the orientation of the teflon pad and mounting strip.
7. Secure - and here is where I had a little problem - new glides in place with pop rivets. (I hadn't use a rivet gun in a while, so I messed up the first pop rivet and had to go to the hardware store to get a replacement. I didn't hold the pop rivet in all the way while I was accuating the gun!)
8. Reverse the process for assembly, and you are all done.

It's simple.

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

1. Remove 2 screws that hold door hinges on.
2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips.
3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free.
4. tilt panel forward and lift of 2 clips at the bottom.
5. Remove the screws under the cover panel which will release the drum holder and lint collector.
6. Lift top of dryer and lift out drum.
TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY.
7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt.
8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum.
9. Re-install the drum and push rear felt to the outside of the drum.
10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder.
11. Insatall lint catch unit with 4 additional hex screws.
12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws.
13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel.
14. Re-attach plastic clips and 2 screws on side opposite of door hinges.
15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes.
16. Check dryer operation.

I inserted the clip

Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!

After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.

Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well

took old one out then i had to strip the connector off new one was to big...

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

Press in the new female latch part with thumbs. Took about two seconds!

Tools required: Stubby socket wrench, 5/16" socket, 1/2" socket, 1/4" socket, #3 Phillips screwdriver, external circlip pliers, straight slip joint pliers. A decently strong electric screwdriver is highly recommended - Milwaukee 2401-20 M12 cordless 1/4" Hex Screwdriver, for example.

Unplug the dryer. Turn off the gas supply.

Remove the screws holding the door hinges to the dryer.

Remove the door and hinges from the dryer by pulling the door and hinges up, then out.

Remove the two plastic thingies (door stops), opposite of where the hinges were, from the front panel of the dryer. Each plastic piece is held in place by two screws.

Grasp the front panel by its top edge, pull it toward you, then lift the panel up and off the clips at the bottom.

There are a couple metal brackets holding the top of the dryer down to the front shroud (the doorway) and frame, one on either side. Each bracket is held in place by two screws. Remove the screws, remove the brackets, then rock the top panel up and back, like the hood of a car.

Remove the screws holding the shroud to the frame. Look carefully. There are two screws that look like they hold the shroud to the frame, but actually do not. Don't remove these screws yet.

Remove the screws holding the plastic duct / lint screen slot to the shroud. These are very long.

Disconnect the wires from the door switch.

Remove the shroud.

Remember the two screws I referenced previously, stating they shouldn't yet be removed? Now's the time to remove them. Do so, then set the panel aside, being careful not to damage any wires. Don't lose the rubber gasket sitting around the circular portion of the duct.

There's a metal cover over the blower wheel. This cover is held in place by a bunch of screws. Remove them all, then remove the cover.

Remove the circlip going around the blower shaft, in front of the blower wheel.

Remove the clamp from around the blower wheel and shaft.

Pull the blower wheel off the shaft.

Install the new blower wheel.

Reinstall the clamp around the blower wheel and shaft.

Reinstall the circlip.

Reinstall the metal blower cover.

Make sure the rear of the drum is resting on the wheels.

Now things become a little difficult, because you have to fight the drum a little bit. Put the panel containing the moisture sensor, front drum seal, and duct into position. (Be careful not to mess up the drum glides. Make sure the rubber seal at the bottom of the vent is in place, sealing the vent to the blower.) Screw the panel into place with two screws, but don't fully tighten yet.

There's a felt seal that is supposed to go between the rear lip of the drum and the rear inside wall. The seal is supposed to be held folded, pinched between the lip and the wall, with the edge of the seal being outside the drum. The seal isn't supposed to jut into the inside of the drum. Use your fingers and some other tool to push the rear felt drum seal out of the inside of the drum. If you use a screwdriver, be careful that you don't cut, rip, or otherwise damage the felt seal.

Do the same with the front felt drum seal.

Carefully inspect the felt seals. You don't want any portion of the seal somehow working its way back into the inside of the drum. Then verify again that the rubber seal that goes between the blower housing and the vent is in place and properly sealing. Now tighten the screws.

Connect the wires to the door switch on the shroud, then loosely screw the shroud in place. Screw the shroud to the vent. Once all the screws are in place, tighten all the screws.

Lower the top of the dryer into position.

Hook a bracket into one side of the lid, position the bracket over the front shroud, then screw in place.

Repeat with the other bracket.

Place the front panel onto the bottom clips. Seat the panel onto the clips all the way, then rock the panel forward into place.

Install the plastic door stops.

Insert the door hinges into their slots, push the door down to seat into place, then install the screws that hold the hinges in place.

Plug the dryer in, turn on the gas, test.

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

I watched the video

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.