MLE23PDHYW Maytag Dryer - Instructions

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

Installed the new part. Worked great!

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.

Remove the door and front cover ,then the top flips up ,remove the front drum support then the drum,remove the snap ring and the pulley

Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.

The repair directions on PartSelct.com made this repair a piece of cake.
Just removed screws holding door and front of dryer.
With these removed it was a simple matter to detach top and get access to internal components.
Two hex screws held baffle in place.
Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.
I also reversed door to make it easier to transfer clothes from washer.
The instructions, detailed drawings and the quality of the part were all excellent.
They had replacement to me in 1 day.
Will definitely use PartSelect again.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

I took the front door off, then i took the the front facing off so i could see in where the idler pulley was. Then I took a couple of screws out so i could get the tumbler out so i could put the belt back on track. I replaced the pulley and then started putting everything back together and now the dryer works like a brand new one. I loved buying parts from here. Cause you are showed how to replace the parts you are wanting to replace. I was very satisfied with everything.

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

My son did the repair work. He took off the door and then carefully unhooked the belt and removed the drum. Replacement on the drum roller kit went smooth, and he then oiled the idler pulley while he was in there. I now have a "quiet dryer" once again!!! Had orderd the wrong part to begin with, but was very easy to return, receive my credit and get the "right" replacement part.
Great Service!!!!