MDE21PNAGW Maytag Dryer - Instructions

Removed the door then removed front panel then removed 8 screws that held the drum in. At this point reached in and removed the snap ring on the wheels and replaced the washers and wheels. Then reassembled it.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

I took the front door off, then i took the the front facing off so i could see in where the idler pulley was. Then I took a couple of screws out so i could get the tumbler out so i could put the belt back on track. I replaced the pulley and then started putting everything back together and now the dryer works like a brand new one. I loved buying parts from here. Cause you are showed how to replace the parts you are wanting to replace. I was very satisfied with everything.

Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.

The repair directions on PartSelct.com made this repair a piece of cake.
Just removed screws holding door and front of dryer.
With these removed it was a simple matter to detach top and get access to internal components.
Two hex screws held baffle in place.
Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.
I also reversed door to make it easier to transfer clothes from washer.
The instructions, detailed drawings and the quality of the part were all excellent.
They had replacement to me in 1 day.
Will definitely use PartSelect again.

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

Replaced the heating element and both thermostats. Hope that takes care of problem! You tube was a tremendous help through video's.h

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

I followed the video instructions which were excellent. Dryer repair was a cinch.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Replaced rear drum rollers and drum belt. Would have been impossible to do unless I had watched the video. [Re-watched video 4 times during repair to make sure of what I was doing.] dryer now works fine. Dryer did throw off a lot of lot dryer felt lint during first post repair use. Customers should let it run one empty cycle after repair.

As per video instructions we took off front and removed drum. We only changed one of the roller support wheel as I could not find any information as to how many I need for my type dryer and parts diagram was deceptive. Showed only one drum support roller.

I re-assembled, checked felts, and wear blocks,(good condition). I cleaned lint, removed coins from baffles, corrected several dents(minor), double checked wire condition and routing (good), finished re-installation, checked balance . all was good, and ran two loads of laundry. very quiet! Thanks

I've had this dryer since it was new It's over 25 years old. and it started to make a high pitch squealing sound when in use. Decided it's time to repair it. a new one is very expensive. So I ordered the parts from this site. When the parts arrived they where Inspected for fit, function and finish. So I proceeded with doing the repair myself. Short Phillips screw driver to remove the two sheet metal screws at the bottom front panel. tilted the panel from the bottom outward and removed it from the main tumbler cabinet. labeled the door switch wires one was yellow & one white. so I would not reinstall them incorrectly upon assembly. removed the front panel. set it aside. then removed the bulkhead panel 5/16" screw in each corner. removed that and set it aside. and there she was, the tumbler. I pulled the tensioner up to loosen the belt, and removed it. then grabbed the tumbler from the inside top slightly picked it upward and slid it out of the cabinet exposing the two rollers and axles one on each side that it sits on. at that point I noticed the drive belt was frayed and slightly worn. came back in the house and got on line ordered a new one from Parts Select it showed up a day later and a perfect match. the rollers are held in place by snap rings at the end of the axles. squeeze them they come off real easy, and on the back side there's a 14mm hex head nut. box wrench works good here to loosen the nut and remove the axles. the original washers are metallic and worn badly, they where making the high pitched squealing sound when they rotated so they came off and where replaced by the ones in the new roller kit and lubed with graphite not oil or grease. Graphite is dry and does not collect all the dirt and debris. put the new washers, new rollers & snap rings back on the axles grooves on the end, hand spun them and they where ready to roll. took the new belt placed it around the tumbler over the exact witness marks that where there so it would line up and lifted the tumbler back into the cabinet aligned the new belt over the motor pulley and tensioner lining it up exactly on the witness marks left by the old belt. slowly slid the tumbler back on to the new rollers rotated the tumbler a couple rotations clockwise to set the belt put the bulkhead back on the front with 5/16" sheet metal screws. in 4 corners, reinstalled the from panel along with the door switch wires and it was done. now the moment of truth. plug the machine in and turn it on!. Bingo! it runs so well you don't know it's even running. after this repair the machine performs even better. it actually takes LESS time for clothes to dry! AJS

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.