YE206KA Magic Chef Dryer - Instructions

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.

The website lists 2 wheels for this model, no info on the flat spot in the shaft. I ordered the less expensive wheel but it did not fit the shaft, got a refund, ordered the more expensive one, it fit with just a little tapping with a light hammer.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

I yanked up the front of the lid, the broken belt laid across the drum like a dead snake. Pulled that out, then removed the two screws holding the front. Using the pliers, pulled off the two wires snapped to the door switch.
Lifted out the front panel, and lifted the drum, (added a bit of a yank to get it out of the two rollers in the back).
Vacuumed out the dust and dead bugs, then tried to figure out how to thread the belt on the idler and motor. (This was the hardest part) the picture that shows the parts is an exploded view, and does not show the way that it goes together. After about half an hour, I asked for help, and we found a slight rubbing on the idler and figured out that the tensioning spring pulls on the lower part of the idler arm, not the top. Putting the belt on, and getting the spring into the hole in the base was tricky, but not hard. Reassembly was straightforward, and took less than 5 minutes. (put in the drum with the belt on it, hook the belt on the motor and idler, push the rear of the drum into the rollers, then put on the front panel, re-attach the door switch, and the two screws holding the front, and close the lid).

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

The repair was pretty simple.
1. unplug dryer.
2. use a med. flat screw driver with some cloth wrapped around the blade as not to chip the paint surface. From the front of the dryer,
carefully pry open the top surface of the dryer. There are 2 points to lift, about 3" from the right side and 3" from the left side.
3. The top will open like the the hood of a car, lift gently, you might have to move the dryer out if you can (if you are on a flexible service connection).
4. Unclip the push bottom elec. switch.
5. Carefully remove 2 sheet metal screws on the top left and top right (from the inside of the dryer cabinet. These hold the front of the dryer in place. You have to remove the front of the dryer to get the drum out. I can't believe that these 2 flimsy screws hold the dryer together.
6. Pull the front panel off, tipping it forward. More on this later, it's really important!!
7. Remove the drum, it's light weight, but bulky.
8. Now you will see the motor assembly and idle pulley.
9. Follow the belt diagram with the replacement belt package.
10. It gets a little tricky to get the drum back in because there's a bit of spring tension on the drum from the belt.
11. You're ready to re assemble. BUT, the next step is really important.
12. Since you have the front panel off, you can get at the lint trap. Yeah, lint. Ever wonder why your favorite Tee shirt gets thinner and thinner? Well, look in the lint trap. I filled a vacum cleaner bag with the hard packed lint.
13. By the way, you have to remove the 2 torx screws that hold the lint trap assembly.
14. Vacuum the whole exhaust pipe while u are at it.
That's it!

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!