YE206KA Magic Chef Dryer - Instructions

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

I yanked up the front of the lid, the broken belt laid across the drum like a dead snake. Pulled that out, then removed the two screws holding the front. Using the pliers, pulled off the two wires snapped to the door switch.
Lifted out the front panel, and lifted the drum, (added a bit of a yank to get it out of the two rollers in the back).
Vacuumed out the dust and dead bugs, then tried to figure out how to thread the belt on the idler and motor. (This was the hardest part) the picture that shows the parts is an exploded view, and does not show the way that it goes together. After about half an hour, I asked for help, and we found a slight rubbing on the idler and figured out that the tensioning spring pulls on the lower part of the idler arm, not the top. Putting the belt on, and getting the spring into the hole in the base was tricky, but not hard. Reassembly was straightforward, and took less than 5 minutes. (put in the drum with the belt on it, hook the belt on the motor and idler, push the rear of the drum into the rollers, then put on the front panel, re-attach the door switch, and the two screws holding the front, and close the lid).

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)

I tilted the unit back enough to scew the new legs into the threaded holes.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

lift top of dryer unscrew the top of the pull out filter from the top of dryer. then unscrew the screws near top on the inside of the front panel and have an old soap container handy to hold up the dryer drum. lift the front panel up for removal and put the old soap container under the drum to keep it from falling out. Then mess around with the idler pulley and look up information under pictures of idler pulley in place with belt in Google to see how the belt fits through it.. Finally replace belt, check front and back of drum to insure proper fit and put the dryer back together to see if all works well. and see if the reason for belt breaking is apparant and more than just old age and use.

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

The repair was pretty simple.
1. unplug dryer.
2. use a med. flat screw driver with some cloth wrapped around the blade as not to chip the paint surface. From the front of the dryer,
carefully pry open the top surface of the dryer. There are 2 points to lift, about 3" from the right side and 3" from the left side.
3. The top will open like the the hood of a car, lift gently, you might have to move the dryer out if you can (if you are on a flexible service connection).
4. Unclip the push bottom elec. switch.
5. Carefully remove 2 sheet metal screws on the top left and top right (from the inside of the dryer cabinet. These hold the front of the dryer in place. You have to remove the front of the dryer to get the drum out. I can't believe that these 2 flimsy screws hold the dryer together.
6. Pull the front panel off, tipping it forward. More on this later, it's really important!!
7. Remove the drum, it's light weight, but bulky.
8. Now you will see the motor assembly and idle pulley.
9. Follow the belt diagram with the replacement belt package.
10. It gets a little tricky to get the drum back in because there's a bit of spring tension on the drum from the belt.
11. You're ready to re assemble. BUT, the next step is really important.
12. Since you have the front panel off, you can get at the lint trap. Yeah, lint. Ever wonder why your favorite Tee shirt gets thinner and thinner? Well, look in the lint trap. I filled a vacum cleaner bag with the hard packed lint.
13. By the way, you have to remove the 2 torx screws that hold the lint trap assembly.
14. Vacuum the whole exhaust pipe while u are at it.
That's it!

i pop the top of the dryer lose and removed the 2 screws that held the front on and installed the new belt and put it back to gethere

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.