YE20JA1C Magic Chef Dryer - Instructions

I watched the video tape

Replaced the thermal shut off and the thermistor located on the heating element bracket.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.

first I went online and took a look at the schematic and realized that two items can shut the complete unit down and would be easy to check. First I checked the door switch with a multimeter then the high limit non-resettable thermostat. The contacts on the thermostat were open which told me it was bad. Went online to www.partselect.com and found the part really easily. came in when they said it would and it was a perfect match to the original (part numbers on the side and eveything). Make sure you correct the problem that caused the unit to overheat in the first place. IN my case the dryer air passages were full of lint. After a good cleaning put it all back together and it worked better than it has in years.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

1- cleared all the ducts. (They were clogged and this is what caused the fuse to open)
2- Replaced the fuse from the kit
3- The dryer stopped working again after 1/2 hour -the fuse blew-up again
4- Altough the stat (the other part included in the kit) checked OK with the multimeter, it was actually defective and did not regulate the temp.
5- changed both parts included in the kit, the dryer worked normally again.

I first made sure there was power to dryer. It was ok so I unpluged the dryer from the socket and afer researching on line I was sure it was the thermal fuse. I check continuity on the fuse and it did not have continuity. So I installed a new fuse and high temp thermostat (they come together)
Just lift top of dryer up and back. In the left rear corner is the heating element. On top of the element is the thermostat. On the right side is the fuse it is a round disc with two white wires attached. The thermostat and heating element need to be removed to install fuse (one screw each and lift out of the way ) . Need to check for blocked lint or like I had the white plastic hose had a kink and need replaced with metal lint hose.

This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

Vacuum out the dryer vent & trap of all the tenant's sleeping bag stuffing, intall the new lint trap and Voila! It works again.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!