YG20FY2 Magic Chef Dryer - Instructions

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

I watched the video tape

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

I opened up the dryer lifting the lid with a putty knife and removed the two screws holding the front. I reached in and removed the belt and removed the drum. I took my shop vac and cleaned all the lint, the door passage to the lint screen extremly full of hard lint. I tested the coils with my multi meter and they tested bad. I also did the test that was suggested by Part Select and again it showed the coils as bad. Once I received the parts about three days, it only took about twenty minutes to install using just a screw driver to replace the coils and the belt went on real easy with easy access to the tentioner. and my dryer now runs more quiet and dries the clothes in half the time it used to take. My belt was still in pretty good shape but I put a new one on since I had it apart any way. My friend had the same problem with his dryer and spent $300.00 for a repairman to do the same thing. I tried to tell him it is not rocket science and very easy to do yourself. Thank you Part Select for the good repair advice as well as the timely delivery of the parts.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

replace two heating coils. Dryer working find.

Installed new coil, helped but have other issues that I'm troubleshooting.

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.