YE205KGA Magic Chef Dryer - Instructions

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

Unplug - use screwdriver to release top latches.
Raise top to more than 90 degrees - hard on hands or head if it falls. Remove wires from door swithch and remove front panel screws, lift off front cover. Remove screws from front paned of blower housing. Remove snap ring - shaft clamp already loose, remove old blower whee and install new one. Use DEEP(spark plug) socket tap new wheel onto shaft, replace clamp and snapring and reinstall panel on housing, put front panel back-install door switch wires before screws, replace top, plug in and test run.(note 1st word correction)

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

I loosened the belt removed the drum, removed the push nut and cracked pulley and replaced both,old push nut was a little stubborn but finally got it off.

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

Took the front of dryer apart removed belt and drum replaced my parts and reassembled.

Absolute First thing to do - Unplug drier from power source.
1st I looked up the parts drawing on line. 2nd Took the front of the drier off . It was held on by two
hex head screws. iIused a four-in-one screwdriver as a nut driver. 3rd. Lifted the front off the two post that held the front on, being careful not to strecth the wiring. 4th Took old wheel off, by removing snap ring with a pair of pliers,it came right of, no puller was needed because the hub was out of round. 5th Pushed the new wheel on, being sure to line up the "D" shape to match the motor shaft.
I could not push the wheel all the way on so I took a short piece of 1/2 copper tubing and used that to drive the wheel into place. The tubing fit over the motor shaft and was smaller than the hub. Be careful to tap the plastic wheel on, you do not want to crack the wheel. 6th Put snap ring on -with pliers. Reassembled front. Finished.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

Remove back panel, looking for access. upon reassembly dropped socket into lint trap. Dissemble again, also dissemble lint trap ducting, found it almost completely blocked by lint, clean and reassemble. Remove front panel and there is the problem of the broken belt. Try to look up online to no avail because I didn't have the proper machine ID, but I did find out where to look. Now with the right info ordered the part. Received in the post about 5 days. Upon reassembly I realized that the adjustor was laying in the bottom, picked up, cleaned inspected, OK, then needed to figure out where it goes, got it, then to figure out how it holds tension on belt. That took a few minutes, well maybe 10 then the old Ford light bulb came on, then installed the belt and adjuster. Replace front panel, slide back into place, hook up wiring and duct. Test, guess what folks it works.

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)