DLEX6500B (ABLEECI) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joaquin from MIAMI BEACH, FL
- Parts Used:
- EBF61496102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker
With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from CORNELIUS, OR
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broke the tub drum
Exchange
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from RENO, NV
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum cracked
Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Aurora, CO
- Parts Used:
- 4581EL2002L, 4400EL2001F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer was extremely noisy
This was all pretty straightforward with the helpful video hosted on this site. The only issues I ran into was I had a seized screw that stripped and I had to drill it out and replace it. Also, I had to disassemble the front and rear a little bit further than what is shown in order to install the new roller axles. I was pleasantly surprised that I did not have to worry about the triangular retainers, because the replacement rollers/axles use an improved metal retaining pin. Overall, I'm very happy and the dryer is nearly silent now. It was a bit of a challenge but I took my time and gave myself breaks throughout the morning rather than banging my head against the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- temeaco from TULSA, OK
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Locker assembly broke
Just unscrewed the original lock and screwed the new one on it was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Mendham, NJ
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Heater wouldn't get hot - suspected thermal fuse
Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from San Francisco, CA
- Parts Used:
- 4581EL2002L, 4400EL2001F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer drum stopped spinning inconsistently and made louder noise when spinning
Viewed YouTube video form parts select to take dryer apart. Very easy to do if you just follow instructions in the video. Nothing too hard to do. Of note the 4 pack roller assembly is a whole unit, so you’ll have to replace the stem unit the old rollers use and not just replace the roller wheels like in the video. That is a different part number from LG. The front 2 are pretty straight forward to unbolt and replace. The back 2, especially one on the left is tighter clearance even with a wrench. If you’re able to pull whole dryer out and take back off, it’s an easier to get the one on the back left.
Also replaced belt just because i had it open, I replaced thermistor previously after getting a Te5 code about a year ago so that helped in taking it apart.
Would recommended doing it all since you’ll have it open.
Once replaced, everything ran again.
Also replaced belt just because i had it open, I replaced thermistor previously after getting a Te5 code about a year ago so that helped in taking it apart.
Would recommended doing it all since you’ll have it open.
Once replaced, everything ran again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Michigamme, MI
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thermal fuse went out
Watched a repair video. Very easy to replace, about an hour to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!