KEYS850GZ0 KitchenAid Dryer - Instructions

After checking the temperature safeties, I replaced the Push-To-Start switch. This did not solve my problem, so I replaced the Timer Switch assembly, which did solve my problem. Both switches are very simple to replace. Unplug the dryer, use your nut driver to remove the 6 screws holding the back control cover. For the Start switch, remove the control knob, remove the 2 screws holding it it. Unplug the wires, turn the switch housing 1/4 turn clockwise, and remove it from the opening. Reverse the process to install the new switch. For the Timer Assembly, just a bit trickier. Remove the knob, remove the 2 screws holding the assembly. Unlike the Start switch, the Timer Assembly has multiple wires. Pull the old timer assembly out, and, one-by-one, move wires from the old Assembly to the new Assembly, being sure to land them on the proper post. Once you have done this, return the Assembly to the mounting hole. A very simple repair. Even though I spent $160 chasing the problem, I still came out cheaper than calling a repairman.

First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran.

Just change the timer as follow taking off one wire on the old timer and connect to the new one, and do the same thing for all of the wires.This way will be not confuse with the connections.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.

One night my wife could not start the Dryer. I took a look at it and realized that the timer still advances, but it will not start.

I called a repair man to take a look at it and he confirmed that it was the timer. He said the total repair will cost me aroun $270.00 Parts and Labor.

I then came online and found partselect.com. I searched for the model number of the dryer, used the repair man tool and found what I was looking for.

It took me less then 10 minutes to take apart the dryer and replace the new part. I saved over $180.00 on labor.

To install,I unplugged the dryer from the power. I unscrewed the dryer top and pulled it out. I then unscrewed the timer and disconnected the wires and reconnected the wires to the new timer.

Screwed back the timer in place and screwed back the face plate. Plugged in the dryer, selected a timer setting and pressed the start button. My wife thinks I am a hero.

Thank you Partselect for the great service.

Ruby

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

Fit great,well please with order!