KEYE770BWH2 KitchenAid Dryer - Instructions

Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!

Repair took about five minutes and saved approximately $70!

Prior to ordering parts i moved the dryer out and took the back off the dryer with a nutdriver. I noticed right a way the heating element was damaged and burnt up. I ordered the above parts and recieved them in two to three days. the parts on my dryer were easy to get to and I just matched up the parts i recieved and replaced them one at a time. It only took a nit driver to remove them and plug the wires back in to the new parts.
the dryer works like new again.

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

Pulled the dryer away from the wall took back cover off the dryer. Used volt/ohm meter to identify the bad element. Ordered the element it came in two days. 2 screws and 2 wires to plug in and we were back to drying cloths

Un plug or remove power before you start. First you would have to remove the rear panel of the dryer. All you need is a quarter inch nut driver. Then look at the bottom right side of the dryer. There you will see the heating duct. At the very bottom is where the element is. There are two screws on both sides( they will all be removed with a quarter inch nutdriver ). After you have removed the four screws holding the element on you will have to remove two wires from the elemet be sure that you mark them and dont mix them up. You will also have to remove the round temperature sensor because you will have to reinstall it on the new element. Then you get new element and reverse the order of my directions. Good luck and be safe ALL WAYS REMOVE POWER BEFORE WORKING ON ELECTRICAL APPLIANCES.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

thought the heating element was bad, once inside the element
looked good, tested continuity , tested good.
further test revealed I only had 110 volts at the wall outlet,traced problem to fuse blown in disconnect box under
the house.
Did not need the heating element.luckily parts select is taking the new element back since I did not use it.
Hope this review helps.

Followed the video .... Also installed another part. which was a kit. the video here showed the third wire being installed. The video on repair clinic did not show where to attach the third wire (orange wire). The Kit and the Thermostat was installed with 25 mins. Thanks

First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****

1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes

I removed the hex head screws from the back of the dryer and removed the back panel, after unplugging the dryer. I tested the various electrical components until I found that the upper limit temp fuse had gone out. Came to partselect.com and found the kit I needed and ordered it. When it came in, I replaced the upper temp limit fuse, and the other parts that came with the kit. I also, since the back was open, used the opportunity to vacuum out the blower fan and as much of the lint as I could get to. Dryer works great now!

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.