KEYS700JQ0 KitchenAid Dryer - Instructions

I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once it is tested and works, let it cool off, then reattach it, put on the backplate and you are done!

There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

1. UNPLUG 2.Undo 8 screws @ back of dryer. Locate heating element midway down on right about 6"x10" has three thermostat wires connected to it undo the 2 screws & 3 wires either order. You will need to pry up GENTLY on the thermostat on the old element. Replace themostat to new element and make a test run to make sure its running and HOTand repeat steps in reverse order...

My husband removed the old (2) thermostats..then installed the new ones...he said the only thing he needed was his battery run screwdriver, and it was really needed!
we are happy with the ordering, delivery, and the ease of replacement of our new parts. Thanks.

Took the back off with a cordless drill with an apex holder. I unplugged the old wires from the old heating element and plugged them into the new heating element. Put the back back on after testing it to make sure it worked and that was it. Since this element was in a housing it was really simple to reinstall the new one.

simply replace vent filter

replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.

First I disconnected the power plug. Next I removed the various knobs. Then I removed two screws holding the control panel to the dryer cabinet. Then I removed the 6 or 7 hex screws holding the cover. There were two screws holding the timer to the control panel. I removed the screws and lifted out the timer. I took the various wires, one at a time, from the old timer and put them on the new timer, when finished I re- attached the new timer and reversed my steps. Once the panel was re-installed, I plugged in the power cord and tested the unit. All was fine.

Wife said the drier was not heating. I looked on the internet and found Parts Select. Followed the instructions to test the heating element, thermal cut-offs, and thermostat. This is really easy, you just touch the terminals with the voltage meter to see which ones are not transmitting current (with the drier unplugged). One of the thermal cut-offs was not transmitting current so I ordered the part Sunday night and had it by Wednesday morning and put it on it about five minutes. Steps:

1. Unplug drier
2. Unscrew back of drier
3. Unplug wires from terminals of the parts shown in Parts Select instructions (one at a time)
4. Get a basic voltage meter (I bought a cheap one at the big box store)
5. Test terminals (touch the red terminal on the voltage meter to one side, black to the other)
6. If the needle moves to the other side, the part is OK, if not order the part and replace.

Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the new box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.

I replaced the thermal cut off kit, and the dryer now had heat. Three days later, no heat; the thermal fuse also did not have continuity. Read on-line that overheating was the most likely cause. So, I checked the exhaust duct for blockage, but it was clear. Then, I removed the exhaust canister at the back of dryer; the entire bottom was filled with lint the size of a softball. The lint was heating up, and when it got too hot, it blew the thermal cut off. Cleaned out the lint, replaced the thermal cut off, and now it's fine. Moral of the story: Remove the lint canister and clean it.

I wasn't sure if the problem was the belt (probable) or the idler pulley assembly (less likely) but the total for both parts was about $26 plus shipping. So why not replace both to be sure?

As it turns out, my original idler pulley assembly does not turn. Rather, it has a concave semi-circular piece that is fixed in place. The belt ran in a groove in that piece.

The replacement part has a nylon wheel that turns. As a result of replacing the idler pulley assembly (which I don't think was necessary to fix my tumbling problem) the dryer runs much quieter. (We used to get a fair amount of squeaking when the belt rubbed).

As for the actual repair (I would rate myself as above average on tackling household repairs), it was about the simplest repair I've ever done. I followed the video provided on this site (excellent video) and it took less than 20 minutes -- cleaning up all of the lint/odds and ends under the washer and dryer took longer than the actual repair.

My only issue (minor) was disconnecting the electric harness. It did not slide as easily as in the video. I had to coax mine a bit with a small screwdriver (make sure your dryer is unplugged!!). I suspect it was simply a function of the harness never being unplugged -- the dryer is 9 years old.

I also felt great because I'm sure I saved a $125 service call (for only $26 in parts and 20 minutes of my life).

Good luck!

Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.

My wife reported that the dryer was not working. I checked it and it seemed to work fine. This went on for about a month or two. Every time I checked it, it started just fine.

Well, she threatened to go buy a new dryer, I took her more seriously. I thought perhaps a thermal protection was the cause. But when I dug into it, I learned that when those trip out, they are permanent (have to be replaced).

I finally noticed loud humming sound the motor made at start-up, when it failed to start turning on one occasion and eventually tripped out the motors thermal protection.

I ordered the new drive motor form PartSelect.com.

Replacing the motor was fairly easy if you like to take stuff apart. One thing that I had not anticipated was that the two foam gaskets on the exhaust duct were dry rotted. I went to my local part supplier to get them. They did not have them in stock. :( While I was there, I asked how much the motor was, they wanted $50 more than PartSelect.com :D

I put it back together without the new gaskets, and it runs like new. I ordered the gaskets from PartSelect and will add them when they arrive.

My wife is happy again, she can bust out the laundry in one day; it had been taking here all weekend.

I learned to take her at her word.

My husband pulled out the old filter and quickly installed the new one. It fit perfectly.

I'm so glad I was able to order the part. The machine looks like new.