1106117235 Kenmore Dryer - Instructions

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

My dryer is probably more than 20 years old. I know, I know, but I decided to fix it anyway. I followed the same steps as the other posters here. However, I almost never fix anything like this and the dryer is in a small space with only a couple of inches of clearance on either side.
The repair took 10 hours off and on over 2 days. You will definitely need another set of hands at various times like when you are unscrewing the fan from the motor shaft and when you are reinstalling the drum and belt.
Getting the motor mount clips off the frame was a huge pain and getting the motor back in place and the clips on correctly was a 3 hour learning experience. Make sure you have all the wires hooked back up BEFORE you hook up the motor mount clips. When you seat the motor on the mounts the wiring hookups need to be almost on the bottom. Check the instructions drawing for placement.
You don’t actually remove the fan cover you just unscrew the mounting screws and push it to the side.
Re-hooking up the belt and belt tightener is not intuitive but you will eventually figure it out. I found some generic dryer belt installation drawings on the Internet that showed me how to do it.
The photocopied instructions that come with the motor are kind of fuzzy after a few generations of photocopying.
In the end, it worked! It is also much quieter now.

the plastic fan can be tricky to get off,hold the pully side of motor with an adjustable wrench and turn plastic nut on fan clockwise.mine busted and i had to order another fan but they are easy to put on. counter clockwise to put back on.(reverse treads)

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

This was a classic easy repair and I am sure saved us bundles on a service call.

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.