11069132412 Kenmore Dryer - Instructions

got my daughter's boyfriend over.. he is like McEiver.. can fix anything with a bobbypin.... he told me what to order, you delivered it in 2 days.. and the dryer was fixed the next day. All it cost me was a roast beef dinner
Much better than that repairman who would have charged a minimum of $100 plus parts... at probably triple your cost...

Thanks to the sep by step instructions I got from part select this repair was very simple. The disassembling was relatively easy, my new maintainance kit came the nest day, the machine was already apart and the parts went in without a hitch. THANKYOU

I watched the video on the websit and it told me and showed me just what to do. Exccelent video, Ordered the repair kit, got it in two days. Job took me about 10 min.

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Kit was easy to install and after making sure the drum gaskets were set right the noises ended.

Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.