11069132412 Kenmore Dryer - Instructions

Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

Took back panel off, and it was really easy putting the new idler pulley in.

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done

pull the back off and replace the pulley.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

removed broken parts & snapped in new catch

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..

I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck