11076132410 Kenmore Dryer - Instructions

Very simple. First, unplug the dryer. Unscrew the 2 screws that hold the lint screen in place and remove the lint screen. Now comes the only complicated part. The video recommends using a putty knife to get the top of the dryer to open. I recommend plastic wedges (you can buy one for less than $1 at a local hardware store; I used 2) because then you will not damage the aluminum, which is very easy to do. Basically you put the wedges (I used two) into the opening and hit then very gently with a hammer and they force the top of the dryer to open. From there you remove the 2 screws that hold the switch in place, unplug the switch (this may take a little bit of effort), plug the new one in, put the screws back in place, put the top back on, screw the lint screen screws back in, put the lint screen back, plug the dryer in and you're good to go. This took all of 10 minutes

This problem occurred Thursday afternoon; after I took out a load of dry clothes, it wouldn't restart. I realized that the switch was busted, it used to click but it was just hanging. Watched the video and ordered it right away. It arrived Saturday morning via Fedex and I installed it in about 5 minutes. It probably took longer to watch the video. 23 bucks and the dryer's running perfectly. I've replaced several parts this way on my appliances, always feels good to do it yourself. Good as new.

Installed new door switch, so, so simple. Unplug dryer, remove lint screen, undo 2 scews located at base of lint screen opening. Use flat head screw driver to pry up dryer top, once open, rest the top against the wall. Now you will see the door switch in the right hand corner at front of the dryer.Open the dryer door , remove 2 screws holding the broken switch, disconnect wire from dryer, click in the new switch, put everything back together, plug in the dryer and go! Super quick and easy, wish I had just done this months ago!!!!

Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.

Removed two screws from under dryer lint screen enabling top to be raised. With top being held up, removed two screws holding door switch then pulled wiring harness apart thus removing old part. Reinstalled new switch in reverse order. Very simple.

Follow the vid it is perfect. The vid came with an email from your company.

Once I had determined that the door switch was broken (the black actuating arm was broken) I ordered a replacement. The procedure to replace it is the reverse of removal of the broken part: unplug the appliance to begin. There are 2 screws that hold the filter frame to the top of the dryer; these are removed and set aside for reuse. The top of the dryer can now be pulled up to gain access to the door switch. Make sure you leave enough space behind the dryer to prop the top up without letting it go backwards. Disconnect the wiring harness plug for the door switch and the unscrew the switch. There are 2 screws accessed from the upper right corner of the open door. Replace the switch, guiding the 2 screws into the mounting holes of the part, remembering to not over torque the screws, connect the wiring harness, close the lid, replace the 2 filter housing screws, plug the dryer back in to the electrical outlet and you should be good to go.

After reading on line that the door switch fixed the described problem 48% of the time I decided to order a door switch first. Very easy to follow the video instructions that were on line. In less than 15 minutes my dryer was working again.

Unplug power supply or switch off breaker that supplies electricity to appliance .. Remove lint screen there's two star head screws that holds lint screen holder to top cover remove them, using a flat head screw driver there are two clips between top cover and body push screw driver to depress clip while lifting corner do in other after top cover will become free from clips raise top. Unplug old switch remove two star screws to free switch from inside dryer door

I followed the accurate video. I'm sure I saved a lot of money over having a repair man come out. Now maybe my wife will believe that I am capable of repairing some things myself... eh, probably not.

followed the very handy installation video. it was easy to repair the door switch as the drum did not stop when it was opened. glad we used your service and would certainly use it again if needed for other items. your prompt attention to shipping was also appreciated. thank you!

Watched a You Tube video one of many available.

YouTube.

Took old one out and put new one in. Popped the top off and took out two screws. That was it.

Disconnect Dryer. Remove Screws of lint trap (2). Slide Dryer Top (Cover) and push up to disengage the plastic clamps. Remove the two screws of the old switch (located inside the door panel - upper right side). Disengage the old switch and fasten the new one. Repeat steps backwards to tight new switch and place the dryer cover.