11078132410 Kenmore Dryer - Instructions

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

Upon receipt of the new vent kit, I removed the dryer from its location and took it in to the garage. This facilitated a roomier work space. The directions were easy to follow and the work to be performed was very easy in this setting.

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.