11078133413 Kenmore Dryer - Instructions

Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

Repair was as straightforward and simple as the videos implied. The most difficult part of the repair was disconnecting the door wiring. It could be more plainly shown in the videos. After that it was simple. The cleanup inside the dryer, lint, etc., took as long as the repairs. An extra set of hands to hold the drum in place while routing the new belt over the drive pulley would have made it even simpler. Runs like a new dryer now.

flipped top up, removed 2 5/16 screws and removed front face. removed drum and belt. removed retaining clips on rollers and removed wheels. replaced all clips and new wheels and installed new belt on drum and reassembled in reverse order

Watched video on You Tube, ordered parts online and used excellent instructions sent with belt and other parts in kit. Turn power off by unplugging cord, lift out lint screen, remove screws in lint screen slot, pry up top of dryer with wood chisel or heavy screwdriver, unplug wires top front of dryer, remove self-tapping screws holding front panel in place, lift out drum, remove and replace all parts included in kit, lifted drum back into place, placed detergent bottle under drum to hold it in place while attaching new belt, asked wife to hold lightweight drum in place while I reattached electrical wires and front of dryer. Lowered top of dryer into place and reinstalled lint screen, Be careful! Panels are thin and cut like a knife. Also the dryer lid can fall if you slide the dryer into the wall while working below.

First off, I was somewhat misled by the website and ordered the wrong parts. I entered my model number and ordered the maintainance kit. The info said it was good for Whirlpool, Maytag and others. I also watched the video which is apparently the Whirlpool. So, the wrong parts arrived. The PartSelect peeple were very helpful in getting me the right parts and getting them delivered promptly. I then found the proper video, watched that and did the repair. Be aware that all models have subtle differences. Mine had two long screws in the bottom of the door frame not shown in the video. I also had a little trouble with the pulley spring. I removed the assembly and then got it all back together ok. Then I lost one of the door hinge screws. It evaporated. The replacement part was like $4 so I used one from the local HD and all is well.

I took off top of drier completely making sure to photograph wiring diagram for timer, then removed front. Laying drier on it's back, I could then install new belt and tensioner without needing a second pair of hands. I tried using bungee cord but found it easier for me to lay drier on its back. I completely vacuumed all areas including back of drier. I found the retainer clips for front of drier to be bent, so I straightened them. I also installed two sheet metal screws in case one of the retainers failed.

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Viewed online video and written instructions that were included in maintenance kit.

Followed the procedure outlined in instructions included with maintenance kit. My dryer did not have a pully wheel on the idler arm. Instead it was more or less a wear bar formed in a semi circle attached to the idler bar. This is what was causing the noise. The dryer wheels were good and the dryer belt was good too after 10 years of use. The parts in the kit were of good quality and fit perfectly. The supplied instructions were easy to follow.

Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.