110C60222511 Kenmore Dryer - Instructions

I followed the instructions from this website. Repair was simple with the video guide. Repair estimates were for $150 -$200, I spent less than $40 for the belt, new tension idler, and new rollers. It runs like new again. Parts arrived in 2 days! GREAT SERVICE! I'll be back and am telling my friends about your site!

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Viewed online video and written instructions that were included in maintenance kit.

Followed the procedure outlined in instructions included with maintenance kit. My dryer did not have a pully wheel on the idler arm. Instead it was more or less a wear bar formed in a semi circle attached to the idler bar. This is what was causing the noise. The dryer wheels were good and the dryer belt was good too after 10 years of use. The parts in the kit were of good quality and fit perfectly. The supplied instructions were easy to follow.

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

Followed instructions that came with part.

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

After watching your video, and reviewing the directions, I was able to change the rollers, the belt and tension bar with ease. The parts cost me slightly under 50.00 and now the noise is gone and my dryer works great. I am very pleased with PARTSELECT and would use them again. The parts were at my house within three days of placing the order !!!

Found the perfect maintenance kit and helpful repair video on PartSelect.com. Factory replacement parts were delivered quickly along with written installation instructions.Never needed them. Just performed the repair while watching the step by step video. Dryer works great, no noise. A very happy customer.

My dryer all of a sudden stopped tumbling. When I opened up the machine, it turns out that the drive belt was broken. I simply put in the model number in PartSelect.com and found this kit that came with the belt, and drum rollers. The belt fixed the tumbling issue, and after replacing the rollers, the machine is as quite as a mouse! The instructional video helped show me exactly what to do and expect. This was my first time fixing an appliance, and it only took me 45 minutes!

I had my laptop next to me and paused the tutorial video
as I did each step to chnage the drum rollers, idler pully and belt. Dryer runs great with no more screeching!

Following the step by step instructions it took longer to clean the old lint out of the bottom of the dryer than to perform the entire repair.The maintenance kit came complete with every moving part(except the motor and drum)and now it runs very quietly.I am all thumbs when it comes to tools but this was very simple.

I simply followed the instructions, replaced the belt, tub support wheels and tension pullie. Could not have been easier. I figured it was worth $47.00 to buy the kit and if it was another issue, at least I saved money vs. a service call. There are only so many things that can go wrong and the belt was the fix. 20 yr old dryer works just like new.