1107012511 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from FAIRPORT, NY
- Parts Used:
- W11778253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Handle broke off of the Lint filter
Removed old filter and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from SANDY SPRINGS, GA
- Parts Used:
- W10612022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
remove, take off , install
just remove 4 screws removed the drum and put the affected part and that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margo from FOX ISLAND, WA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maura from Burbank, IL
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint screen was broken - replaced it with a new one.
There were no repairs - I just ordered a lint screen because the screen on the last one pulled away from the frame and wasn't doing a good job of catching the lint. Took approximately 2 seconds to push the new one in the slot.
Fast efficient delivery from Parts Select.com.
No need to publish this I'm sure.
Fast efficient delivery from Parts Select.com.
No need to publish this I'm sure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy (Hairways) from WOODMERE, OH
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint screen had hole and looked like it was scorched
Just slide out lint remover and inserted new one. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beatrice from WALTHAM, MA
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced the dryer lint screen filter
removed the old damaged filter and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Tucson, AZ
- Parts Used:
- W10612022
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Made a metal scraping sound
Took dryer apart. Should've started with You tube videos so I took more apart than I needed.
Got all the parts I needed from Parts select.
Fixed it and works great.
Got all the parts I needed from Parts select.
Fixed it and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from LAKE FOREST, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Heat stopped after a few minutes
Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from BEVERLY HILLS, FL
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dryer overheat
Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from COLLIERVILLE, TN
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Gas dryer would heat but shut off as it warmed up.
Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from FULDA, MN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drum roller were worn out
flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Bonham, TX
- Parts Used:
- 279769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was not getting hot enoug. I determined the higher thermostat was faulty.
Remove the back, just a few screws, after you unplug the dryer. Disconnect the wiring terminals to both the low and high temperature thermostat. Take both units out with a nut driver and replace. Reassemble the unit the same way it was dismantled. Partselect is a great place to order whatever you need. They almost got here faster than I could place the order. Great service, keep it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SYDNEY from BOSTON, MA
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a new filter screen for Kenmore Dryer
Pulled out the very old worn out and damaged filter screen and replaced it with a new filter screen.
Was this instruction helpful to you?
Thank you for voting!