11084422610 Kenmore Dryer - Instructions

Repair was not successful

Simply put it in the exhaust hole.

Lifted top of dryer using putty knife. Took front panel off using socket wrench. Slipped drum belt off an took drum out. Vacuumed out entire interior. Replaced rollers an clips and reassembled!! Saved $100!!! Thank you!!

very smooth with your video instruction help

Removed (2) Philips screws from the lint filter at the top of the dryer. Used a standard screwdriver to pry open the top of the dryer (it hinges back toward the wall). On the inside of the front panel removed a bolt with a socket on the right and left side. Disconnected two wires from the door safety switch (Make sure to unplug the unit first). Lift up on front panel and remove it from the slide connectors at the bottom on right and left sides. Under the drum on the right side pull drive belt slack towards motor and slip off of the pulley. The drum should come out freely. Both rollers are visible remove the triangle clips and the rollers will come off. On lower roller support use needle nose pliers to remove the washer clip that holds the vertical support arm. Reverse this procedure to assemble the dryer again. There is an excellent video that is supplied online. Watch it first , it was very helpful to me.

Raised the top of the dryer and removed the front panel. Then removed the drum to gain access to the drum support rollers. Used the the flat screwdriver to remove the retaining clips holding the wheel in place. Slid the new wheels in place and popped the clip back on. Slid the drum in and put the front back on. The installation video online was extremely helpful.

watched repair video and fixed dryer.

Took off the out cover of the dryer unit. Removed the drum. Then replaced the roller

I had already disassembled dryer to confirm problem, then I ordered rollers. Once rollers arrived ( and quickly I might add!) I replaced rollers and reassembled in less than 15 minutes - parts ordered were perfect fit.
Thanks!

took the drum out and replaced the wheels there was nothing to it

The first and best thing I did was watch the instructional video. This was very helpful. I removed the lint trap and two screws, then pried the top off using a putty knife as described in the video. I I disconnected the wiring harness and the two screws holding the front panel, then removed the panel. Next, I removed the belt from the drum and removed the drum. I had a little difficulty removing the clips holding the rollers, but was able to pry them off after a few minutes. I installed the new rollers and reassembled everything. Note: I used the nut driver to push the new clips onto the roller pins. The problem was resolved and the dryer is working fine!

I removed the 2 screws under the lint cover and popped the top of the dryer up and back. I then unplugged the safety switch wire on the upper right of the front cover. Next I removed the 2 screws holding the front panel on and popped it off while supporting the drum. I took the drum out after taking the belt off it. One of the rollers had the rubber stripped off it. This was kind of curious since I put in a full kit including belt and rollers a few months ago. I replaced the damaged roller and reassembled. I will save the second roller in case it happens again. There is no apparent damage to the drum so I have no idea why the previous roller didnt last.

before i describe the repair let me tell you about the shipping. I ordered the parts early Friday afternoon and recieved then Sat. morning, almost like they were E-mailed to me. A++ The repair was a simple task that anyone that could find the problem could fix. WORD

popped open top, removed two springs on lower end of front panel.took off same panel, pulled drum forward, pulled jesus clips from roller pins ,took off old rollers and replaced with new rollers and clips.

Take out the two screws the hold the lint screen filter compartment in place. Remove the two top clip retaining screws, and lift the top LOOSE and turn it a bit out of the way. I didn't find it necessary to remove the top. Unclip the two wire electrical connector at the top - front, and remove the 1/4 " screws the secure the front. Lift the front up and out of the way. Slide the drum belt off the tensioner and moter pulley and slide the drum out the front. Remove and install the rollers ( and its just that quick) and while your in there. Clean up a bit ... cant hurt right? Especially on and around the motor. Reverse the procedure but rotate the drum a few turns to properly position the belt. Total E.T. is maybe 20 minutes and on a 1 - 10 scale for "degree of difficulty ". This is about a 2. Save the money and do it yourself.