11084422610 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- james from Fredericksburg, VA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
one of my rollers fell to pieces
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Madill, OK
- Parts Used:
- 349241T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise while in use
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from southgate, MI
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
drum support roller was squeaking VERY loud
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from albuquerque, NM
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer tumbler made a loud noise
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Avon, CT
- Parts Used:
- 349241T, WPW10359270
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Worn bushing on bottom drum roller
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsey from Lancaster, PA
- Parts Used:
- 349241T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer was making a loud rattling noise and shaking
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from VASS, NC
- Parts Used:
- WPW10359270, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The drum made a lot of noise while turning. The dryer shook
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramon from Los Angeles, CA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making a lot of noise while running.
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from OAKLAND, TN
- Parts Used:
- 279771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer would not heat and the timer would not turn as it should
I replaced a bad thermostat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ava from BALTIMORE, MD
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer making excessive noise; then continued to blow circuit
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from EVEREST, KS
- Parts Used:
- 349241T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
rollers had been new too long!
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HELOISA from BOCA RATON, FL
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Was too old
I just changed for the new one! 2 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BLOOMFIELD, CT
- Parts Used:
- WP694674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!