110C61102011 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kendahl from Leander, TX
- Parts Used:
- 279816
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dryer wouldn't heat
I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larold from WILLMAR, MN
- Parts Used:
- WP3977767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer would not heat on any heat settings.
First I watched the repair video on-line at this site After pulling the dryer away from the wall and unplugging the 220 volt power cord I removed the back panel with the 9 screws. I then unplugged the wires to the thermostat/heating element. With an ohm meter I discovered that the heating element was good and the high limit thermostat was bad. I ordered the high limit thermostat from this site on a 2 day shipment. When the part arrived I installed the part and the wires. Plugged in the dryer for a quick check for heating. Replaced the back panel and moved the dryer back into position. Dryer works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheldon from macon, GA
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dryer want heat up
they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MYRTLE BEACH, SC
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
noisy dryer
followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from GRAFTON, IL
- Parts Used:
- WP3387134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Clothes never completely dry
I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from TUJUNGA, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Clothes taking too long to dry.
The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from PORT ALLEN, LA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Belt
My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports
Was this instruction helpful to you?
Thank you for voting!
The Dryer would not heat up
I unplugged the machine and removed the back panel with a 1/4" socket. I unplugged each thermostat in turn and pulled them out. The internal bias was a bit tricky to remove without breaking the tabs or wires. I then placed each thermostat back in and replaced all the wires. Not bad at all. Weird thing is the dryer heats just fine now, until I put the back panel on; once I replace the back panel, it will not heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from waukesha, WI
- Parts Used:
- WP3387134
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
dryer would heat up once on a full hour cycle
i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off,disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Tucson, AZ
- Parts Used:
- W10612022
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Made a metal scraping sound
Took dryer apart. Should've started with You tube videos so I took more apart than I needed.
Got all the parts I needed from Parts select.
Fixed it and works great.
Got all the parts I needed from Parts select.
Fixed it and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from FAIR OAKS, CA
- Parts Used:
- WP3977767
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Unit was tripping the circuit breaker after about 10 minutes of drying time
Unplugged the unit, removed the back panel of the dryer and then removed the thermostat panel. Disconnected the wires on the thermostat and changed out the thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SIMI VALLEY, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Pushing start button made buzzing sound but dryer didn't start.
The repair video provided for this model 110.97584810 gave erroneous info. It says to remove the back vent cover. The back on this model is not removable. I wasted an hour trying to remove back and top of dryer before discovering that the bottom front panel below the door pops off. Then the cover of the blower must be removed by removing two screws. The thermostat part can then be accessed and replaced as shown in the video. You'll need a 1/4" rachet to remove the screws as there isn't space to use a nut driver. Note that the statement in the video "This repair is done all from the back" is completely wrong. It is done entirely from the front. It can be done without even moving the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from PHILADELPHIA, PA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dryer was making loud noises.
Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Rupert, ID
- Parts Used:
- W11415783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this instruction helpful to you?
Thank you for voting!