Models > 110C61102011 > Instructions

110C61102011 Kenmore Dryer - Instructions

Jump to:

All Instructions for the 110C61102011
106 - 120 of 551
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
joe from southgate, MI
Parts Used:
349241T
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
drum support roller was squeaking VERY loud
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry from Lindsay, CA
Parts Used:
279441
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
The dryer tub became jammed, unable to turn.
I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JENNIE from NORTH ROYALTON, OH
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Drum quit turning due to broken belt
Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from SCHENECTADY, NY
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Broken dryer belt
Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from BEAVERCREEK, OH
Parts Used:
WP3977767
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
taking to long to dry
put the high limit in , plus the temperature , plus the exhaust switches
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
scott from missouri city, TX
Parts Used:
279816
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
no heat from the dryer
first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Audrey from North Miami, FL
Parts Used:
279816
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
dryer was not heating anymore
removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Josh from Madill, OK
Parts Used:
349241T
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Loud noise while in use
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Colorado Springs, CO
Parts Used:
WP694089
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers
Fan blade had to be removed , was broken off from motor.
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from WOODLAND HLS, CA
Parts Used:
WP3387134
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Dryer wasn't getting real hot and took a few cycles to dry.
Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
moua from FRESNO, CA
Parts Used:
279816
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The thermo cut off is dead.
I bought a new thermo cut off and replaced the old one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Enrique from LA VERGNE, TN
Parts Used:
279816
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Dryer would not heat
Looked on YouTube and found these guys. Followed their instructions and no problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from ATLANTA, GA
Parts Used:
WP3387134
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
no heat
still no heat.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anne from GLEN COVE, NY
Parts Used:
WP3387134
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
dryer ran but was not making heat
followed the instructions on this site. to find the problem. checked the coil, thermostats and fuse with my multimeter. Found the bad one, order the part and put it in. It was very simple and now my 20 year old dryer works again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
moujin from CARMEL, IN
Parts Used:
WP3977767
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
no heat only
repairing is pretty straightforward.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 110C61102011
106 - 120 of 551