11068132410 Kenmore Dryer - Instructions

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

Kit was easy to install and after making sure the drum gaskets were set right the noises ended.

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.