1107192311 Kenmore Dryer - Instructions

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports

The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.

they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.

Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

I ordered the necessary thermal cut off and fuse from Part Select. The process was easy, when i came home from work my husband installed the piece in a matter of minutes and we were back in business of drying clothes.

still no heat.

Turned it on it's face,removed bottom back panel.Checked the heat coil and had closed circut. Checked the thermal cut offs one had a closed circut one open.So I orderd the kit ,replaced both . On with the panel,stood it up,plugged it in and WHALA!! Heat and happiness.

Remove the back, just a few screws, after you unplug the dryer. Disconnect the wiring terminals to both the low and high temperature thermostat. Take both units out with a nut driver and replace. Reassemble the unit the same way it was dismantled. Partselect is a great place to order whatever you need. They almost got here faster than I could place the order. Great service, keep it up.

I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.

followed the instructions on this site. to find the problem. checked the coil, thermostats and fuse with my multimeter. Found the bad one, order the part and put it in. It was very simple and now my 20 year old dryer works again.

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

Unplugged dryer, removed back panel, checked thermostats & heating coil with ohm meter, found one stat with broken terminal and one that was bad. Ordered them from this site. Received them in record time, did the installation and was back in business drying clothes. Thanks for video & great service.