1107192311 Kenmore Dryer - Instructions

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

Watched the videos available. Opened the top and saw tub jumping. Unplugged and removed front panel. Saw tub rollers were broken or melted. Removed tub watched more videos, and installed the felt belt I got from PartsSelect. Trouble removing the tub rollers, but finally got them off. The axles had a sticky residue which I removed with 220 grit sandpaper. I installed new rollers I had bought locally. Reassembled dryer. Worked quietly and smoothly, and it no longer shut itself down. Worked well for one day when it started.s loud noise with bumping. I found both rollers had lost their outer rim , and the tub was running on hard plastic and there was sticky residue back on the ankles. I stopped there.

I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.

Ignor installation video. it is for a different model dryer. The part is not accessed from rear. It is accessed from the front panel. Disconnect power. Remove two screws below front panel with cross head screwdriver. Swing panel up until it releases. No need to disconnect wires just put front panel down beside the dryer. Thermostat located right in front on duct easy to identify since it has four leads. Remove wires with needle nose pliers. Remove thermostat with nut driver. Contacts are labeled but hard to read. Hold thermostat so the lead number 3 (the 3 will be upside down) is on the left. Connect blue wire. White wire to top. Purple wires to bottom and right. Reverse removal procedure and you are done.

Remove the back panel. Remove wires from top sensor and bottom sensor and remove old sensors. Install new sensors and replace wires. Dryer works great.

Replaced Thermal Cut-off kit and Heating Element

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

Watched video and removed lower cover of dryer then removed and replaced the thermal cut-off .Dryer works great now.

remove back of dryer and install part same as old part was installed

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

Tested the two thermostats, thermal fuse and the hi limit cut off for conductivity. The hi limit tested open. The others tested closed. Replaced the hi limit. Cleaned lint from the lint duct assembly after removing the two hex head screws that hold the assembly to the blower housing. The lint was packed in there solid. Cleaned up all around. Reassembled everything. Looks and works like brand new. Access was completely from the front panel. CAUTION: The rear panel is spot welded on although it has eight or nine hex head screws also, and when you remove them, the holes don't line up for replacing them. Took a lot of head scratching and time to get things lined up so the screws would go back in again. Don't try to remove the rear panel like the video shows.

Our dryer produced no heat. I thought that it was the electrical heating element because this part had failed a number of years ago. But when we received the heating element, and I opened up the back of the dryer to install it, I found that the element was OK. (Visual inspection as well as using an ohm meter.) I then ordered the thermal cut-off kit, (which was over a week in getting to us because Fed-Ex misdirected the shipment). Once the kit arrived it was very simple to remove the Allen-head screws on both parts, install the two new parts, reconnect the wires, replace the back panel on the dryer and hook up power and the dryer vent hose. The dryer works just fine.