1106708620 Kenmore Dryer - Instructions

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.

Pull out the old lint filter unit; push in the new one.

Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.

all that was required was to push the catch into the slot notools needed.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

I realized from this issue years ago that it was porbably the heating element. I took the dryer to the garage and remove the back and figured out how to get the heating element out. Once I had it out it had a break in the coil so I knew I needed that part. I hit parts select on line and ordered the part. I left everything in the garage and waited for the part. In a couple of days it came and I put it in and took the dryer back to the laundy knook, gave it a test run and Its all good!

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.