11067086600 Kenmore Dryer - Instructions

Unplugged dryer, removed bottom front panel, removed fan cover. I used a 1/4 ratchet to remove 2 screws and the old fuse. Installed new fuse, fan cover, and front panel. Dryer works great!

Remove old filter, throw it away, replace with new filter.

Dryer is still in pieces after two weeks, dependent upon my time and ability to work on the project. I usually dry my clothes on an outside line, anyway. I especially appreciate Steve's videos demonstrating step-by-step procedures for disassembly, part installation, and reassembly. Very thorough. I timed each presentation---five minutes for one, less than ten for the other. I watched the videos several times and took notes, so I would have the procedures in front of me while working on the unit at the other end of the house, I'm 77, forgetful. When I disassembled my unit, I noticed several rusted areas, so decided not to complete the project until I could get to the store for paint. As a primary care-giver for a severely dementiated 79-year Old Lady, I have to arrange for a relief to go shopping. That's why the machine is still in pieces. Got the paint, though, so back to work---eventually. When I disassembled the dryer, tucked away in the bottom was a very informative TECH SHEET, the discovery of which ticked me off that it wasn't provided with the owner's manual. At the bottom it says, "For Service Technicians' Use Only." In my house, I'm the "...Service Technician...," chief cook and bottle washer, launderer and litter box attendant.

Followed the video.

Unplug from electric ? outlet. Set the meter to ohm setting, check part ,no reading. Remove old part ,check new part with meter ,get a reading of 11 or more mA. Install new part and blower cover done.

Just insert filter.

Easy manually

This was so easy to take apart and put back together following the repair video. I figure my family saved $200.00 by doing it myself.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Exchanged old for new.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

After reviewing the video of the fellow popping out the old door catch with a putty knife and popping in a new one, I tried that myself and there was no way it was going to come out without applying enough pressure to tear up the finish on the door. Tried the option of compressing the catch vertically with pliers and could get top or bottom out but not both. Believe my I have a garage full of tools and am very handy and this method was not going to work on my dryer. Finally removed the door and laid on carpet, took out all the screws and removed the catch from the back by squeezing with pliers. Replaced with the catch from the other side after doing the same.Re-assembled no problem. Ordered a replacement that I put in the unused side for next time.

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.