1107057700 Kenmore Dryer - Instructions

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

watched your video on 'how to' and did it like man showed..no problem

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

Removed top, then remove front panel, then removed the drum, and the idler pulley assembly. Then added new parts, and reversed procedure to assemble back to new.actually runs better, now. Dryer is approximately 30 years old.

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!