1106517710 Kenmore Dryer - Instructions

I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

removed the broken part and replaced with the new one

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.

I took the back off of the dryer and then removed the lint chute assembly. Next came the top removal which was a little tricky because the top locks were installed incorrectly from factory. After about 20 minutes for a 2 minute job, the top came off. Now I was able to remove the front and the drum. This left me access to the motor. The hardest part of the whole job was removing the blower wheel. Being made of plastic you must be careful not to brake it while grabbing hold of it and applying torque to the motor side. This process takes two people. My wife helped me and it took about 5 minutes. Leave the motor mounted for this. Once the wheel was off, the motor was then removed, the new one was installed and the process was reversed for assembly. Not very difficult overall and saved me a whole lot of money. Make sure you vacuum out all of the dust since you have the whole dryer apart. It will probably be the last time you see inside it and the dust sure builds up inside after 12 years! Thank you Partselect!!

First I removed the rear panel of the control sectio and the main rear panel. I checked the switches and fuses. The fuse for the dryer vent was giving an intermittent signal, so I replaced it with one I picked up at a local repair shop.
Since I had started working on it, and due to the age, I went ahead and ordered a motor, belt, and drum rollers and replaced these as preventive maintenance.
Once you realize how everything comes apart, it is not a very dificult job to overhaul the complete dryer.

I read several customer feedback articles to find one with problem similar to mine. After eliminating the thermal fuse, it was obvious my motor was bad. Watched the video and easily removed motor. Took motor to a repair shop and they confirmed it was bad. Replacement motor arrived in two days (yes...2 days). Unbelievable quick delivery. Easy to reinstall---only took about an hour. Hey, it would have cost $500-$600 to replace this dryer! Now I feel like I have a new dryer for $80!

Replaced the cap over the door switch so when the door closed the switch was engaged

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

Was informed that I had a bad dryer motor and no warranty. Unplugged the unit. Removed to screws in the lint trap slot. Used a small blade screw driver to pop the 2 clips at the front of the dryer top. Lifted the top and rested it up against the wall. Removed 2 screws holding the machine front panel. Removed the front panel and removed the tub. Couldn't get the blower loose from the dryer motor so I cut it off with a hacksaw. Moral if you are going to replace the motor go ahead and by the blower too. It is less than $20.00. Popped 2 clamps loose holding the motor in and removed it. Placed the new motor in the unit. Strapped it down and attached the new blower. Plugged it in, put the dryer back togehter and tried it. It worked.

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.