1106517710 Kenmore Dryer - Instructions

our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.

Pulled back panel off, then removed entire front body. Accessed the blower and the lint cover and removed. Removed drum and belt. Removed motor and replaced, reassembled and plugged in and it worked. Thank you

Repair went well your video was a great help. The motor was hard to disconnect from the blower and fan side.The shaft that you hold with the adjustable plier was hard plastic type of material and wanted to keep slipping and the edges wanted to round off and not hold in the adjustable pliers. I had to use a small pipe wrench with teeth to break it loose. The only other problem was the ground screw in the new motor had an odd type of head on it and took a special type of nutdriver attachment to loosen it and attach the ground wire to the new motor.

Removed and replaced motor. In the process of removing old motor, the blower wheel had to be unscrewed from the rear shaft of the motor, in order to remove the motor. In my case, the blower wheel had seized up on the rear shaft and could not be unscrewed. It had to be cut off and it also had to be replaced. The dryer now works fine. Tip: I watched an internet video (repairclinic.com)about the procedure before I started. Very helpful!

My dryer is probably more than 20 years old. I know, I know, but I decided to fix it anyway. I followed the same steps as the other posters here. However, I almost never fix anything like this and the dryer is in a small space with only a couple of inches of clearance on either side.
The repair took 10 hours off and on over 2 days. You will definitely need another set of hands at various times like when you are unscrewing the fan from the motor shaft and when you are reinstalling the drum and belt.
Getting the motor mount clips off the frame was a huge pain and getting the motor back in place and the clips on correctly was a 3 hour learning experience. Make sure you have all the wires hooked back up BEFORE you hook up the motor mount clips. When you seat the motor on the mounts the wiring hookups need to be almost on the bottom. Check the instructions drawing for placement.
You don’t actually remove the fan cover you just unscrew the mounting screws and push it to the side.
Re-hooking up the belt and belt tightener is not intuitive but you will eventually figure it out. I found some generic dryer belt installation drawings on the Internet that showed me how to do it.
The photocopied instructions that come with the motor are kind of fuzzy after a few generations of photocopying.
In the end, it worked! It is also much quieter now.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I removed the back before I relized that the motor was under the drum. I removed the front and the drum and accessed the motor. I used a small flat head screw driver to prythe brackets that held th motor in place. I had a bit of a problem removing the motor from the fan. Then I read the web site and figured out that the treading was a LEFT thread. Still had some problems and ended up removing the pully wheel and using a pipe wrench to get the fan off the motor.

I wish I had taken a picture of the pully and belt to see how it went back together, but it went back easy enough.

Very pleased with my effort and guess I saved about $300 bucks on the repair, and the 2 plus weeks to get the guy to my house.

the plastic fan can be tricky to get off,hold the pully side of motor with an adjustable wrench and turn plastic nut on fan clockwise.mine busted and i had to order another fan but they are easy to put on. counter clockwise to put back on.(reverse treads)

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.

Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the dryer. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Screwed in light bulb and glass protector

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!