11066952690 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phillip from Breinigsville, PA
- Parts Used:
- WP3390291
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element not heating up.
Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistance from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Boswell, OK
- Parts Used:
- 279769
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer wouldn't heat.
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Annapolis, MD
- Parts Used:
- WP3387223
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Clothes were not drying on auto sensor.
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- atolfo from allentown, PA
- Parts Used:
- WP3390291
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
dryer will not,dry clothes,but drum run
Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from KINGSPORT, TN
- Parts Used:
- WP3390719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer would not start, showed F40 code
Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from WEST PALM BCH, FL
- Parts Used:
- W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer squealing loudly during operation
Unplug dryer from 220VAC outlet
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from STATE COLLEGE, PA
- Parts Used:
- 279787
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
dryer did not run
remove top, front, drum, fan fan housing, replace motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ARITON, AL
- Parts Used:
- 280114
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10314173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Making a racket.
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucy from CHADDS FORD, PA
- Parts Used:
- WP3387223
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Hard to reach the screws inside the dryer They were on the door side of the dryer and hard to reach, especially if you are a abig guy.
Removed the dryer door, unscrewed lint vent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Genette from CLEVELAND, MS
- Parts Used:
- 661570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Belt was raffling and there was aloud knocking sound
Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from RAVENSWOOD, WV
- Parts Used:
- WP3387747
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No heat from dryer.
1.Removed lower dryer cover - two screws. 2.Tested heating element circuit including high temp cutoff, - Heating element circuit was "open" so I first tested the heating element - "open" so I removed one screw on the side and removed the element - element broken. 3.Ordered the part - good price and the deliver was great, three days. 4. Cleaned any lint up and Installed the new heating element and front panel 5. Heated right up - probably saved myself a good $100 for less than thirty minutes of work!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Bainbridge, PA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dryer would shut off mid way through cycle and give an E1 error code
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeline from PANA, IL
- Parts Used:
- WP8577274
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
YouTube video dated 9/28/2015
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LAKE ZURICH, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Intermittent squealing sound while dryer running
Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel
Was this instruction helpful to you?
Thank you for voting!