1106507822 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from PLAINFIELD, IL
- Parts Used:
- WP691366
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer drum wasn't turning
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Oakland, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Marion, KY
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Noise in dryer when dryer was turned on
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from LaGrange, IL
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
dryer stopped and smelled of smoke.
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Was this instruction helpful to you?
Thank you for voting!
Buzzing sound while start button pushed. then shut off after 30 seconds.
Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from OAKLAND, TN
- Parts Used:
- 279771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer would not heat and the timer would not turn as it should
I replaced a bad thermostat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from COAL CITY, IL
- Parts Used:
- 239087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum rear seal bad
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Rupert, ID
- Parts Used:
- W11415783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Perris, CA
- Parts Used:
- WP230131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door cables broke.
I replaced the springs and cables in the dryer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsey from Lancaster, PA
- Parts Used:
- 349241T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer was making a loud rattling noise and shaking
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this instruction helpful to you?
Thank you for voting!