11096561210 Kenmore Dryer - Instructions

Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

After researching and finding correct replacement unit placed order and waited to receive. Screen is located top of dryer so replacement simple and fit was perfect.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

Unplug dryer, remove two screws in lint screen door, using a pry bar or stiff putty knife, gently pry up on both front corners to release the clips holding the top down. Use a 5/16" nut driveer two remove the two screws inside at the top of the front of the dryer, remove the two wires on the door switch. Open door enough to get your hand in to support the drum, now lean the front out at the top and let the drum rest. Grasping the front at the top on both sides gently lift up to release the clips securing the bottom front. Release the door springs,open door and replace the hinges. Reverse to reassemble.

First, I slid the top forward to release it and then pivoted it about the clips along the back edge. Second, I removed the open/closed door sensor. Third, I removed two screw on the inside of the front panel and slide the front panel up to release it from the clips near the bottom edge of the panel. Fourth, I removed the dryer drum that fell out as soon as the front panel was removed.

With the drum on the floor (carpeted), I installed the front seal and the back seal after removing the old seals. I then applied the glue supplied with the back seal to the back seal. Next, with my spouse's help, I placed the drum into the dryer frame while positioning the seals, the drum driving belt, and the front panel. This step was the most 'interesting' of the whole repair. I replaced the two screws on the inside of the front panel. I spun the drum to ensure that the seals were in the correct position.

Finally, I replaced the door sensor and dropped the top into place.

just slide the new filter in.

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint trap so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.

Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!

Repair took about five minutes and saved approximately $70!

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.