DE08 Kenmore Dryer - Instructions

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

Used a flash light to see, reached in and installed new bulb above the door

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.

4 screws to open it up,pull out the wheel and there it is on back . Pretty easy..

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

remove the old one and put the new one...!!! Easy

Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.

I pulled the old handle off and pushed the new one on.
No problem at all.

Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minutes or less.

Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.

Follow the instructions from YOUTUBE to replace the new drive belt..

watched vidio from the site.just follow the instructions, And was able to fixed the problem.