DE08 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lilly from CROSBY, TX
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
handle fell off
stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from west milford, NJ
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from ERIE, PA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove plastic and insert
inserted the lint catcher into the opening to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from West Bloomfield, MI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic handle in dryer broke off.
All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Nora Springs, IA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom part of handle was loose
Opened up the package and took off existing door handle. The new one snapped right into place. This took all of 10 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from pleasant grove, AL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic Door Handle Cracked
Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEMPHIS, TN
- Parts Used:
- WE18X25100, WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old dryer filter was cracked and bulb burnt out
Easy peasey! Just Removed/Replace screw-in type bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from MORGANTOWN, WV
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was cracked and the metal "D"-Ring was broken on my GE cloths dryer
This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from WHITE LAKE, MI
- Parts Used:
- WE9M13
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket ripped
It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LOVELAND, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bud from RCH CUCAMONGA, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Snapped right into place , less than a minute, if that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tahir from ARLINGTON, MA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer leaving stains on clothes
Shortly after a piece of felt (the duct felt seal) was visible on the drum intererior, the dryer started making metal-on-metal squeaks. A few weeks later it started leaving'machine part' type brown/black marks on clothes. With the model # it was quite easy to find and order the correct part, which arrived a few days later. The accompanying video made installation quite straightforward, even for someone who's NEVER worked on a dryer before - even though the model used wasn't the same. Over half the repair time was to clean out lint and dirt from the various exposed parts. Overall, an easy and effective repair that solved the staining issue. Follow the video and you won't go wrong.
Was this instruction helpful to you?
Thank you for voting!