11081932511 Kenmore Dryer - Instructions

Replaced Thermal fuse, hardest part was getting behind the drier to disconnect the gas & vent line.

Removed the old screen and simply put in the new one

Replaced all 4 sensors. Still no display. Ran my thumb across all control buttons several times. Machine showed life. Looking good, but low heat. Replaced the heating coil, and now we have a new, 13 year old machine.

NOTE: Please make sure the dryer is un-plugged any time you are reaching into the access panel with your hands or a tool. There are exposed connections everywhere. After using the diagnostic testing instructions (usually attached to the inside of the front panel) I determined it was a faulty Thermal Fuse. The PartSelect video instructs you to take half the dryer apart to access the Thermal Fuse, but I found it easy enough to just access it with the front panel removed. I used a small 1/4" drive socket to remove the single hex head sheet metal screw holding the Thermal Fuse in place. I then slid the 2 wires off, noting which went to which lug. Installed the new thermal fuse and after starting the screw by hand, tightening with the small socket wrench. It is a bit tricky to reconnect the wires as you are doing it all by feel, but it's a lot easier than taking half the dryer apart. Also, make sure you check the exhaust path for obstructions, that might be why the ThermalFuse blew in the first place.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

There were two tricky parts - one, was locating the part to repair on the dryer. One set of instructions said it was on the back of the dryer behind the panel. Once I removed that panel I realized that the thermal fuse was on the front. After I identified where the part was (bottom front), the second tricky part was getting to the screw. You just need a mini-socket set and relatively small hands. A magnetic light that can attach to the dryer while you are working is also useful. This would have been a 30-45 minute job had I known precisely where the part was that needed replacing. Otherwise, this was relatively easy.

Unplugged dryer from electrical outlet. Removed top panel from dryer to get instructions for location of parts. Removed front panel to get to fuse and thermostat. Had to purchase small socket wrench to access nuts because of small space and angle of difficulty. Removed both parts, and replaced with new parts. Plugged dryer back in. Tested for heat. Working properly.

The repair, replacing the thernal fuse was easy, just one screw and then remove and replace by disconnecting and reconnecting two wires. It did take a bit of time to find which part was defective. I first removed the back panel and front panel and the drum to get at the igniter and flame window. I checked continuity of these parts as well as the gas solenoids and they all checked out ok. The thermal fuse was last on my list. It read as an open circuit. I temporarily jumpered the two wires at the fuse and checked that the igniter would now heat up. I spent over one hour removing the ductwork and giving the unit a thorough cleaning with a shop vac.

Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.

An online help site lead me to believe the problem was the gas igniter. After ordering that and installing it I discovered that wasn't the problem. I took a look at the schematic which is in the electrical compartment and found that there is more than one thermal breaker. I found the other one, ordered and installed the part and had it running within 30 minutes. I had to access the back of the unit, remove the back cover with a socket wrench, unscrew the thermal breaker and re-install the new one with no special tools.

My wife and I thought our dryer was done and we were looking at a large replacement costs. We started googling and found this site and watched the video. We are were 99% sure it was the thermal fuse. We received within 2 days and thought we would be in there for over an hour. Turned it was less than 10 minutes, we watched the video clip on how to install on our laptop as we did it.

We will always be buying parts from this site and have told a ton of friends/family to check this site out.

It saved us so much money!!!!

Took back panel off dryer, unscrewed old part, put on new one. Easy fix. Dryer works great again.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

The major issue was getting the dryer out and cleaning it all up. That's what took the time but it was worth it to clean out the lint in the ducts, etc.. Putting the thermal fuse was a snap thanks to the great feedback received when I got this web site and read the previous responses.

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......