DE27S6WPMC Gibson Dryer - Instructions

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.

There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.

We had the rear drum bearing replaced about three years ago. The company that serviced it was quick to take our money for the diagnosis but took over a month (and a threat to call the better business bureau) to actually make the repair. This time I decided to do it my self as I had successfully replaced the the drum drive belt two years ago. The dissassembly was challenging but the repair it's self very easy. I opted to use nuts and bolts to attach the bearing assembly rather than the supplied screws as they did not want to tighten. Reassmbly was a bit of a challenge regarding the drum drive belt but I had the entire repair done in less than an hour.

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.

Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.

This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.

unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!

The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.

First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.

Replaced belt

googled frididaire dreyer parts
found Partselect
ordered parts {they were here in less time than what they stated}
watched Film {very helpful}
Me and My son installed both parts less than 1 hr.
VERY HAPPY WITH PARTS AND SERVICE
Will order from PartSelect when something else Breaks
VERY happy
Dave..

removed the drum out the front and replaced

first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.