DDC0580VA General Electric Dryer - Instructions

my two twin boys Mike and Curtis age 14 did the repare they toke of the front of the dryer then the top put the belt around the drum then put the top and front back on then went to the back and removed the panel and put the belt on the pulley then set the tension wheel then put the back cover back on
the repair was easy I watched to make sure they did it right and did not have to tell them how I am very proud of them they do great work
finding the part was easy and it was here the next day after I ordered it and it was only sent 3 to 5 work days. You guys have a great web site and fast shipping thanks for the good work!

The drum slides on my dryer had worn down to the point that an opening formed that allowed clothes to enter the gap and get pinched between the spinning drum and the door. This would leave a mark and sometimes a cut on the clothes. To repair: open the door and undo the screws above the door opening that hold the top on the dryer. It's hinged in the back so it swings up from the front once the screws are removed. Undo hex head screws on either side at the top that hold on the front of the dryer. Also loosened the same at the bottom of the front panel (includes the door). Pull the front off of the dryer. This exposes the drum slides on either side in the front of the drum. They're fastened to the frame of the dryer. Undo the hex head screws (2 each) and remove drum slide, then replace. I recommend one slide at a time so the other one helps hold the dryer in place. The kit includes both slides. Pretty easy once I discovered how worn the old slides were! The drum turns much easier and quieter now too!

Easy as 1-2-3. I took off the top hinge screws in order to lift up the top of the dryer.

I then took off the front dryer piece with the door intact. The lint filter was in the front door section.

I released the wiring clips to the front of the dryer and lowered the front of the dryer down gently. there is enough slack with the wiring if you disconnect the wirre clips.

I removed the old broken belt. ThenI gently lifted thr dryer drum enough to slid in the new belt with the ridges down. Look for the old belt line (worn area on the drum) and slip the belt up on the drum to that point.

Then I replaced the wiring with clips and put the front of the dryer back together.

Going around to the lower back of the dryer, I unscrewed the back plate where the exhaust comes out. It was 8 screws with a socket.

Once the back was off, I pulled the dryer pully to the right and fed the reamider of the belt through both pulleys ensuring that the ridged side was on the correct side of the pulley. The pylleys match the ridges on the belt. I rleased the tension on the movavle pulley and it was done.

All I had to do was button the back up and do a "dry run" I quick have the drum a half roation from inside the drum with the door open. Then it was all gravy. I was done and saved myself a good deal of money. Look on the net for pics to make thing easier for you. There are people out ther who will NOT charge you for this info.

First i removed the lower rear inspection plate to see what the problem was.
next i removed the screws in the front top panel.
next i lift the top back,the rear hinges held it in place.
next i removed the bolts that held the front panel in place,but before i removed the panel i removed the wires that were connected to the front elements and disconnected then,
next i removed the front panel,then i place the new dryer belt over the dryer drum,but first you have to rise the drum up a little to get the belt under it.
next i put all the front panels back in place,make sure you reconnect the wires that you removed earlier.
next i moved to the back panel, there i position the belt over the dryer drum,then i place the belt over the motor drive pulley, then i pull down the tension bar roller to the left and place the belt over it.Then i replace the rear panel in place.plug in the power core and turn it on. finished. After over 35 years this is the first time i had to replace the belt,matter of fact this is the first time i had to replace anything on this dryer, washers will that is a different story. but the dryer runs great maybe for another 30 +years LOL.

Disconnect and clean all duct work.

Note: Lint is combustable, save yourself the disaster of a dryer fire.

Position dryer face down on floor.
Access rear of unit, vacume clean.
Upright unit.
Access front of unit by removing sheet metal screws above door to float the lid.
Using screwdriver gently seperate drum at top from housing. Hold open with wedges.
Thread new belt through hole a foot or so.
Tape belt to drum near drum center.
Rotate drum until belt is fully around.

Note: Taping new belt to drum will assist you in reassembling. Belt will not fall off drum when unit is face down on floor.

Remove wedges and resecure sheet metal screws to top of unit.
Place the unit face down again.
Ensure belt clears all front mounts.

Note: gentaly pull drum from mount and slide belt between.

Remove old belt and idler pully.

Note: replace the idler pully with every new belt it will save you time later.

Install new idler pulley and rethread in new belt.
Rotate drum to access and remove tape attaching new belt to drum.
Upright unit and test.
Re-attach access panels, reposition unit and
re-attach duct work.
Done

Removed the rear access panel (8 - 10 bolts), checked the pullys. Opened the dryer door, removed 4 allen screws at top and lifted the top of the dryer (like a hood on a car). Removed a screw (phillips) on each side (inside) pulled open the front and worked the belt around the drum. Placed belt onto pullys, plugged in checked for proper rotation of drum then unplugged and installed screws and bolts. - Fairly easy, saved a bunch from a service call. I also found 15+ years of lint inside the dryer. Vacumed and cleaned the inside -it even dries faster! Sorry Honey - No new dryer this year - Now can I go hunting?

snapped in new latch

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

I removed the old lint filter and put the new one in! Grateful to find this item for my "antique" dryer.

removed cabinet
removed drum
dismanteled blower assy
found a tooth brush in the assy.
replace blower wheel
checked timer and heating elements
reassembeled
advised my wife of the problem

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Just changed lint trap by removing old one and replacing new one.

Simple - took out the defective filter and replaced with the purchased part. The hardest part was figuring out the right lint filter. The extensive info on PART SELECT was very helpful.

Had to totally disassemble the dryer, working from front, back and top. That finally allowed access to the heating element. Then it was a simple matter to pull out the old burnt coils, stretch the new coils to the recommended length specified in the provided instructions, string them through the insulators, wrap the ends around the appropriate posts and tighten down the nuts. Then reassemble the rest of the dryer and test run. Perfect.

After opening the front door there are screws that are holding the top to the door. Take those screws out using a Phillips screwdriver. The top should lift up and rest at a near 90 degree angle.

The door has two screws at the bottom that need to be taken out. Once those are out there are two screws on both sides at the top holding it to the frame. Remove those as well.

Before you remove the front you should document the wiring for the door light switch. I took these off to give the door a little extra room so I could rest it on a toolbox without taking all the wires completely off.

Once the door is free, on the back there is a metal plate with two screws in it roughly in the middle of the unit. Unscrew the top completely but leave the bottom screw in and just slightly loosen it. This will allow it to swing down out of the way without the need to completely remove it and have one more part to put back together in the end.

What this plate is covering is the center of the drum. There is a small metal tab that you can push on and it will push the drum out so it can be removed. Gripping the drum, you can lift it out by guiding it through the notches on each side where the drum protrudes.

With the drum removed you'll see the motor and idle pulley. On my model the pulley was attached to a metal rod that was spring loaded. The pulley is held on by a small tension washer that was easily removed with pliers. Installation was somewhat more difficult but mostly just getting it lined up and started. Once on the rod it was easy to push it into place.

With the new pulley installed it's time to install the new belt. To do this first put the belt over the drop and then replace the drum back into the frame. Once the drum is pushed back into the hole it will support itself.

Now you need to remove the panel on the back to get access to the motor and pulley. This panel has a lot of screws. Once that's off you can then guide the belt over the motor and get the idle pulley to put tension on the belt.

Once that is complete just replace all the screws you removed, plug it back in and watch as your new belt moves the drum once again.