GTMX100ED1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from VICTORVILLE, CA
- Parts Used:
- WE01X20374
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken timer knob
removed old broken knob just pulled it off,replaced with new one took about five seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MURFREESBORO, TN
- Parts Used:
- WE01X20374
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was cracked and wouldn’t turn properly
Replaced the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from STRATFORD, CT
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint filter was broken
remove the broken one and replace it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from MOUNT CARMEL, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy squeaking drum...
I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NORTH PLATTE, NE
- Parts Used:
- WE4M533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer internal gears had stripped and dryer would not start
followed video exactly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lilly from CROSBY, TX
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
handle fell off
stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEW BRITAIN, CT
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer bulb burned out
Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- De Ann from FORKS, WA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was catching clothes and would not release without very hard pulling, consequently twisted and grease marked fabric, ruining items.
I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from GREEN BAY, WI
- Parts Used:
- WE14X25080, WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer became very noisy when you turned it on to run
I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Kilgore, TX
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
squeeky drum
Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Milford, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clothes were catching between the drum and front of dryer. Also was squeaking at times.
Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from west milford, NJ
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Round Pond, ME
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer was making a really loud, high pitched squeak and eventually a grinding noise
I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from ERIE, PA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove plastic and insert
inserted the lint catcher into the opening to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from ACKERMAN, MS
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer start knob was cracked inside so you couldn't turn to start the dryer
This was so easy. I used needle nose pliers to reach in and remove the metal clip which had slipped off of the inside of the knob and was on the post the knob was supposed to attach to. Next, I lined up the flat side of the "D" of the inside of the knob to the flat side of the "D" on the post and pushed it in until it snapped into place, and I was done. The dryer now works like new.
Was this instruction helpful to you?
Thank you for voting!