PTMN930EMWS0 General Electric Dryer - Instructions

Used a flash light to see, reached in and installed new bulb above the door

Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.

Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.

Remove top (2 screws) and front (2 screws), snap out old drum bearing, put new slides in new drum bearing and install in dryer. Reinstall front and top of dryer.

remove the old one and put the new one...!!! Easy

I followed the directions I found on my tablet on youtube.

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconnect the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

open door, remove two screws from below the top. gently remove the top from the side and bottom panels. remove two 5/16 screws from front panel hold panel so it does not fall. the bearing assembly will come out by moving the bearing towards the dryer, and pulling upwards. replace with new bearing, use 4 front dryer slides and reinstall the top and front panel. can be done in less than 15 minutes

Screwed the light bulb into the socket (duh)

The parts came very quickly, and they were the exacxt parts which made installation very easy.
Just open the dryer door, there are 2 screws to remove right above the dryer door that holds the top plate of the dryer. slide the top of the dryer top off by pulling up and ouyt towards you. There are 2 screws that hold the front of the dryer, remove the 2 screws and the front of the dryer will come out towards you. The drum will fall a litttle towards you.
I let the dryer front lean on my leg and snapped out the bearing and drum slides replaced it with the new one. Reverse the order of taking it apart
Now my dryer sounds as quiet as the first day I bought it.

Piece of cake, mostly because of the nice exploded drawing that was on the site when ordering the parts, it was easy to identify what was needed and order it.

I will never call a repair man again :-)

Pull the old lint trap out. Slid new one in

This took less than 10 minutes to complete. 1) pull off the top of the dryer and remove the two screws that attach the front panel to the side panels. Once you pull the front panel towards you, away from the side panels, you can remove the front bearing. Be sure to be careful not to pull apart the wiring on the left side of the front panel. If you do, it is easy re-attached by hand. The front roller bearing of he drum can be removed by hand. Simply pull upward, with a steady pressure, on the bearing. It will snap out with this gradual pressure. The slide can be inserted by hand, with the two gray slide at 11 and 1 o'clock and the wite slide at 10 and 2 o'clock. The new bearing will snap into place by hand. Carefully insert the light bulb into the hole in the top of the new bearing whle snapping into place. The web site provides a good diagram that illustrates the various pieces and assembly. Once the bearing is in place, lift the dryer drum and set on top of the bearing as you re-attach the front panel to the side panels with the screws removed earlier. Replace the top by snapping back into place. Less than 10 minutes.

Removed two screws to remove top to access drum. Removed two screws to remove front panel. Easily removed drum bearing and snapped in new bearing. 4 Glides were slid into slots. Only one problem. My service parts list called for drum bearing #WE3X37. I was sent #WE3M26. I was assured this was the right part for my dryer. Although the part did fit, I was unable to use the existing light because the the hole on new bearing was too small to accommodate it. Replacement of drum bearing would not be necessary if GE would put visible labels on dryer warning consumers of preventive maintenance of glides that wear.