PTMN930EMWS0 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Louisville, KY
- Parts Used:
- WE3M26
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer was not heating at any level and it was making noise while rotating
First, I unplugged the dryer, pulled it out into an open area. I then removed the vent hose. I opened the front door and removed the 2 screws that hold the top panel down. Once removed, I lifted off the top which exposed the drum. Next, I remove the 2 screws along each side that allows the front door panel to detached. I noticed that there was damage to the plastic bearing and 3 bearing pads were missing. That was the source of the noise. Once the door panel is lifted off the cabinet, the wires to the safety switch must be pulled off so the door can be set aside out of the way. Then I went to the rear and remove 2 more screws that gave access to the motor, wiring and the tensioner for the dryer belt. Once I gained access to the belt, I slipped it off the tensioner and drive pulley. This allows the drum to be removed from the cabinet. WE wrestled the drum out before realizing that we should have removed another 2 screws securing the sides of the dryer to a cross support under the front of the drum. This would have made the removal of the drum much easier. Once the drum was removed, I had access to the heating coils. Upon examining, I saw that both had burned out at the far left terminals. Directions that came with the new heating elements gave clear instructions on how to install. It's a little daunting to thread both elements through all the insulators, but patience paid off. Everything went back together easily and the dryer started up and heated up just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff D from NEW MEADOWS, ID
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tod from Cherry Valley, CA
- Parts Used:
- WE03X29897, WE3M26, WE03X37318, WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud squeaking
remove to screws in front to take of top. Then remove two screws holding the face on. change parts re assebmle. extra hands nice for holding drum while remounting face. Nice and quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from WINDHAM, NH
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was making a very loud squealing sound
I followed the step by step instructions provided by Video! Very informative, easy to understand and follow! If I can do it myself, anyone can! Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Glenshaw, PA
- Parts Used:
- WE3M26, WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Squeal When Running
2 Screws hold top on, removed top, 2 more screws hold front panel with door on, removed front panel. Unclipped front drum bearing installed new one with new sliders put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BALTIMORE, MD
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking
Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from BOCA RATON, FL
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Drum Bearing Cracked. Bearing Slides worn or totally missing
I followed the video instructions provided to me by this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doreen from fall river, MA
- Parts Used:
- WE03X37317, WE3M26
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
squeeking and clothes getting cought
I followed the instructional video that was given online. The parts fit well, and was easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from MURRIETA, CA
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The old drum bearing was worn down due to years of usage.
Remove the old bearing assembly and Replaced with the new bearing assembly with new bearing slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from NEWTON, IA
- Parts Used:
- WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer made noise upon startup which quieted after a few minuts. Sounded like loose coins in the drum.
Removed two screws inside the door at the top of the frame. This allowed the top to be lifted and slid to the left a bit which allowed the front of the dryer to be removed. The Drum Bearing was held on with plastic tabs and the Bearing slides just fitted over a small tab then into a slot. There is a "knockout" for the light which is removed. The entire process took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!