PSKP333EB0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- leah from Ocala, FL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob cracked and dryer wouldn't start
Doesn't get any easier. Lined up the D shape on dryer and timer knob and just popped it in. Working great. I wanted to comment on the super fast shipping. I have never had anything ordered and delivered to my home so fast. It took less than 24 hours to get to my door from the time I ordered it and we chose just the regular ground shipping. Amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Elko, NV
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer timer knob had cracked and when turning the knob it would not rotate to setting desired
I went online and ordered the part number WE1M654 and it came within 2 days and just pulled the old knob off and inserted the new knob and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandy from sugarcreek, OH
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob would not advance
took the knob out of the bag and snapped it into place...all done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Ledbetter, KY
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle spins on switch shaft
Took new knob out of bag,slid new knob on. Worked great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from easton, PA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher door switch
unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naples, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not switch on whenon/off lever was pulled accross
Switch off the circuit breaker supplying power to the dishwasher.
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Missouri City, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
unable to set the dryer timer
I matched the flat part of the knob to the dryer part and pushed into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrilan from North Charleston, SC
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No problem at all.
I did as the video instruction showed me. I used the pliers and with one pull the metal piece came off and I just put the new knob on it did not take a minute.It was so easy. I am so happy to know that I can get my parts at a great price and do it myself. I have a service plan through my electric company that I pay a fee monthly and if I need services for any appliances there is an additional $25.00 for services and that does not include the part needed to fix my dryer. I ordered my own part with shipping and handling and it still came out less than $25 with no additional fee. I am very satisfied that I now can order parts and do it myself. Thank you PartSelet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Austin, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic timer knob broke and spun around freely
I grabbed the broken knob firmly and pulled it straight off. I took the new knob and pressed it firmly into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ricky from vero beach, FL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stripped knob
I saw the video and it was just as it was shown!! although there was one gliche....I didn't need pliers!!!It came soooo fast thx PartSelect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from VANCOUVER, WA
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the knob turned but the dryer didn't work
replaced the knob, and the dryer worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Hewitt, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knob on dryer had striped
At first i tried to repair the old knob before ordering one with tape and glue.kind of a mans thing you know and needless to say that didn't work so for a little while the man thing was we would adjust a crescent wrench to fit the shape of the shaft to set our time on the dryer. i looked all over our home depot stores and lowes here in town and no one carried the part. my wife Angela decided to look on line and see if anyone carried a part like this. thanks to you guys we were able to order the part and it came in and while i was at work my wife called me and said the dryer is fixed. she just fit the new knob on the shaft and it works like new. thank you part select you made my wife happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaVerne from Cincinnati, OH
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was cracked & slipped over settings.
Simply pulled off old Knob and pushed on new Knob. Saved a house call plus repair fee.
Was this instruction helpful to you?
Thank you for voting!