GFMN245GL0MS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clarke from Grapevine, TX
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeek when dryer was running
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Wynnewood, PA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb dead
remove the old one and put the new one...!!! Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EDGEWATER, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
take the old dryer lint screen out
Hand replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from CEDAR RAPIDS, IA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out
Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from THIBODAUX, LA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inherited machine, lint filter missing
Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUDITH from FRUITA, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Monroe Township, NJ
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb
Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.
on the inside is the bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from FARR WEST, UT
- Parts Used:
- WE17X22217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!