PSKS333EB0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis G from Naples, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Holes were not threaded on rear bearing kit
Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from easton, PA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher door switch
unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from Norwalk, CT
- Parts Used:
- WE22X35337
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The lent filter protector broke
removed broken part and replaced it altogether.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from San Francisco, CA
- Parts Used:
- WE22X35337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grid Slide -3 plactic nubs broken slide was loose.
Take old grid slide and pannel off. Clean lint trap wire framework and replace. Make sure this trap frame fits snug against the door, otherwise it puts pressure on the new slide. This is the second time I have replaced this Grid Slide. Slid new pannel into grid frame. Ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carolyn from sherman, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the knob was cracked and the dryer would stay on settings..
pulled the old kob off and examined it and replaced it with the one i ordered...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BIll from Vero Beach, FL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer knob would not turn as plastic was broken.
Removed small metal band on shaft and installed new knob.Very simple but the video that came with e-mail was helpful as I did not realize the metal band had to come off till I saw the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Houston, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer knob was broken
took off the broken timer knob and put the new one on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Hewitt, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knob on dryer had striped
At first i tried to repair the old knob before ordering one with tape and glue.kind of a mans thing you know and needless to say that didn't work so for a little while the man thing was we would adjust a crescent wrench to fit the shape of the shaft to set our time on the dryer. i looked all over our home depot stores and lowes here in town and no one carried the part. my wife Angela decided to look on line and see if anyone carried a part like this. thanks to you guys we were able to order the part and it came in and while i was at work my wife called me and said the dryer is fixed. she just fit the new knob on the shaft and it works like new. thank you part select you made my wife happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naples, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not switch on whenon/off lever was pulled accross
Switch off the circuit breaker supplying power to the dishwasher.
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Austin, TX
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic timer knob broke and spun around freely
I grabbed the broken knob firmly and pulled it straight off. I took the new knob and pressed it firmly into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leah from Ocala, FL
- Parts Used:
- WE1M654
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob cracked and dryer wouldn't start
Doesn't get any easier. Lined up the D shape on dryer and timer knob and just popped it in. Working great. I wanted to comment on the super fast shipping. I have never had anything ordered and delivered to my home so fast. It took less than 24 hours to get to my door from the time I ordered it and we chose just the regular ground shipping. Amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hopatcong, NJ
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud screeching noise
I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.
Was this instruction helpful to you?
Thank you for voting!